Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
When the E.LEVEL knob is turned up to MAX, the unit switches to “effect sound only.” The delay time can be set within the range of 400 ms to 2000 ms. Using the Effects HOLD Up to 2 seconds of performance content is recorded, then played back repeatedly. You can also layer this as you perform something else, then record these together (overdub). You can keep the recorded content playing continuously as backing and produce other special effects. “Using the HOLD Function” TAP This is a tempo delay that lets you set a dotted eighth note delay time for the performance tempo by pressing the DELAY pedal in time with the performance tempo. * The delay time can be set within the range of 46.5 ms to 1500 ms. 1. Set the TYPE knob to ‘TAP” The pedal indicator flashes in time with the current tempo. 2. Press the DELAY pedal in timing with the tempo more than two times. The reference tempo is determined by the time interval between each press of the pedal. The reference tempo is calculated in terms of quarter notes, and the delay time setting is the dotted eight note as referenced to the reference tempo. The pedal indicator flashes in time with the tempo. Timing Delay Sound TIME knob Adjuts the delay time. * When the type is set to “HOLD” or “TAP,” operating the TIME knob produces no effect. FEEDBACK knob Adjusts the amount of feedback (number of repeats). Turning the knob to the right increases the number of times the sound repeats. * When the type is set to ”HOLD,” operating the FEEDBACK knob produces no effect. E.LEVEL knob Adjusts the volume of the delay sound. When TYPE is set to REVERSE, this adjusts the balance of direct and effect sound. Adding a Delay Synchronized to the Performance Tempo Using tempo input, the delay time can be set within the range of 62 ms to 2000 ms. You can set this regardless of whether the effect is on or off. 1. Select the delay type. (except HOLD, TAP) 2. Hold down the DELAY pedal for at least two seconds. • If the DELAY pedal is pressed when the effect is on, the pedal indicator goes out, and the effect is turned off. • If the DELAY pedal is pressed when the effect is off, the pedal indicator turns red, and the effect is turned on. When you continue to depress the pedal, after two seconds the pedal’s indicator starts to flash, and the tempo can then be set with the effect on. Here, the delay time is indicated by the value set with the TIME knob. 3. Press the DELAY pedal in timing with the tempo more than two times. The delay time is set according to the time interval between each press of the pedal. The pedal indicator flashes in time with the tempo. * Press the pedal to set the tempo while no guitar sound is playing. * When the type is set to “PAN” or “SPACE PAN,” the delay time is set to half the interval between the presses of the pedal. 4. Hold down the pedal switch for at least two seconds to complete the tempo setting. The effect goes on, and instead of flashing, the pedal indicator will light. * The tempo may become confused momentarily when you go from Step 3 to Step 4. * If you move the TIME knob after finishing this setting, the delay time corresponding to the knob position takes effect. Using the Effects Write Procedures (p. 21) When the Tempo Has Been Set The delay time stored in a Patch (p. 20) is determined as follows. • If it is within the delay time range that can be set for the type currently selected, it is stored without change. • If it exceeds the maximum delay time that can be set for the type currently selected, the maximum value for the type is stored. • If it is less than the minimum delay time that can be set for the type currently selected, the minimum value for the type is stored. (Example) When TYPE is 100–500 ms When the delay time for the tempo setting is 600 ms: Stored as 500 ms. When the delay time for the tempo setting is 80 ms: Stored as 100 ms. Using the HOLD Function 1. Set the TYPE knob to HOLD. The unit goes into recording standby and the pedal’s indicator flashes at a fixed interval. * After switching to HOLD, wait two seconds before you carry out the next operation. 2. Press the DELAY pedal to start recording. Recording starts when you press the DELAY pedal. Hold down the pedal switch for the duration of the recording (the pedal indicator flashes). 3. Release the DELAY pedal to stop recording. Playback of the recorded content begins simultaneously (the CHECK indicator remains lit). * The maximum recording time is 2 seconds. If the DELAY pedal is held down for more than 2 seconds, the recording stops automatically, and the recorded content is then played back. * An oscillating sound may be audible with extremely short recording times. 4. When layering recordings, repeat Steps 2 and 3. 5. Adjust the volume Adjust the volume of the playback sound with the E.LEVEL knob. 6. Press the pedal switch to stop the playback (the pedal indicator goes out). The unit returns to recording standby, and the pedal’s indicator flashes at a fixed interval. * When play...