Évaluations - 2, GPA: 3
(
)
)
|
Facilité d'utilisation
Utilice el cable USB para conectar el PCR-30/50/80 al sistema. 2 3 3 Coloque el Interruptor POWER del PCR-30/50/80 en la posicion ON (encendido). Si desea obtener detalles sobre la configuracion de Configure el dispositivo MIDI en el software secuenciador. Para obtener mas aparatos MIDI, consulte informacion sobre el aparato MIDI de entrada/salida que debe seleccionar, el manual del usuario para consulte el apartado “About the ports when using a USB connection” el software que este (pag. 159). utilizando. Con esto se finaliza el procedimiento para conectar el PCR-30/50/80 al sistema Macintosh, instalar el controlador MIDI y configurar el controlador. Operation The PCR-30/50/80 is a controller that transmits MIDI messages. You cannot perform using only the PCR-30/50/80 by itself. You will need to connect it to a sound module or computer. The various controllers ([R1--R8], [S1--S8], [B1--B6], [L1--L3], [P1, P2]) can be assigned almost any message you want to get the control you need for your particular setup. For details on the messages that can be assigned, refer to “Controller settings” (p. 126). 114 Connection and MIDI data flow This section explains how to make basic connections for the PCR-30/50/80. * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. * Use only the specified expression pedal (EV-5; sold separately). By connecting any other expression pedals, you risk causing malfunction and/or damage to the unit. When using MIDI connections fig.connect-usb * For an explanation of the items in the diagram, refer to “About the ports when using a USB connection” (p. 159). AC adaptor MIDI OUT MIDI IN MIDI sound module (sold separately) DP-2 (sold separately) EV-5 (sold separately) PCR-30/50/80 MIDI OUT MIDI IN PORT 1 PORT 2 / BULK RECEPTION BULK TRANSMISSION Connection and MIDI data flow When using a USB connection * If V-LINK is ON, PCR 1 and PCR 2 messages will be sent both to USB and to the MIDI connector. * For an explanation of the items in the diagram, refer to “About the ports when using a USB connection” (p. 159). USB cable AC adaptor Roland DP-2 (sold separately) It is not necessary to connect the AC adaptor if you are using a USB connection. However, with some computers, the PCR-30/50 may not operate when powered from the USB bus. In this case, set the power switch to the DC position and connect the AC adaptor. EV-5 (sold separately) PCR-30/50/80PC USB EDIROL PCR EDIROL PCR MIDI OUT EDIROL PCR 2 EDIROL PCR 1 EDIROL PCR MIDI IN MIDI OUT MIDI IN MIDI OUT MIDI IN PCR-30/50/80PC USB EDIROL PCR EDIROL PCR MIDI OUT EDIROL PCR 2 EDIROL PCR 1 PORT 1 EDIROL PCR MIDI IN V-LINK OFF V-LINK ON PORT 1 PORT 2 / PORT 2 / MIDI OUT DEVICE MIDI IN DEVICE BULK RECEPTION MIDI OUT DEVICE MIDI IN DEVICE BULK RECEPTION BULK TRANSMISSION BULK TRANSMISSION Basic operation Basic operation How to switch modes You can switch modes at any time, as shown below. Mode Switcing modes Explanation PLAY mode (p. 117) When you turn on the power, the PCR-30/50/80 will start up in PLAY mode. Transmit MIDI messages by playing the keyboard or operating the controllers. MIDI Channel mode (MIDI CH) (p. 118) Press the [MIDI CH] button. Set the transmit channel (current channel) for the keyboard and bender lever. Program Change mode (PROGRAM CHANGE) (p. 119) Press the [PROGRAM CHANGE] button. Transmit program change messages on the current channel. Bank mode (BANK) (p. 120) Simultaneously press the [PROGRAM CHANGE] button and [MIDI CH] button. Transmit bank select messages (MSB, LSB) on the current channel. Memory mode (MEMORY) (p. 121) Press the [MEMORY] button. Recall a memory set from internal memory into the current memory (p. 136). Snapshot mode (SNAPSHOT) (p. 122) Simultaneously press the [MEMORY] button and the [MIDI CH] button. Transmit the current values of all controllers ([R1--R8], [S1--S8]) at once. Panic mode (PANIC) (p. 123) Simultaneously press the [PROGRAM CHANGE] button and the [EDIT] button. Stop "stuck" notes or other problems with the sound on a connected MIDI sound module. Edit mode (EDIT) (p. 125) Press the [EDIT] button. Assign MIDI messages to the controllers, transmit/receive bulk data, or make system settings. You are returned to Play mode once a setting or a process has been completed within the other modes. If you want to return to Play mode without completing a setting or operation, press the button for the current mode (i.e., the button that is lit). Alternatively, press the [CANCEL] button. The setting you were in the process of making will be discarded. 116 Basic operation PLAY mode When you power up the PCR-30/50/80, it will start up in PLAY mode. The display will show the current channel (p. 118). * The PCR-30/50/80 will start up according to the Startup Memory settings (p. 164). With the factory settings, it will start up with the GM2 MEMORY. For the messages that are assigned to each controller ...