Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
VS-100: System program version 1.50 or later Driver version 2.0 VS-700: System program version 1.30 or later Windows driver version 2.0 Mac driver version 1.0 * There is no need to update the OCTA-CAPTURE. Operating Requirements NOTE • The DIGITAL input connector is used in order to synchronize the VS-100/VS-700 with the OCTA-CAPTURE. You’ll need to obtain a coaxial cable separately. • This setup cannot be used at 192 kHz or higher. • An internal hard disk drive that’s 7200 rpm or faster is required. • In order to use this setup at 96 kHz or higher, a separate SATA hard disk drive is required as the audio recording destination. (This setup will not work with a USB hard disk.) • Depending on the application you’re using, the operating requirements may exceed those listed above. Copyright © 2010 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. Roland is a registered trademark of Roland Corporation in the United States and/or other countries. Updating the VS-100/VS-700 Updating the VS-100 You’ll need to perform the following updates in order to use expanded I/O functionality. • Update the driver to version 2.00 or later • Update the system program to version 1.50 or later Updating the Driver First, you need to download the driver from the Roland website. The downloaded VS-100 driver version 2.00 is in a zip format archive file. Right-click the file’s icon, choose “Extract All” from the menu that appears, and extract the file as directed by the on-screen instructions. In order to update the driver, you’ll first need to uninstall the old driver. For details on the installation procedure, refer to the Readme.htm file created when you extract the archive. You must read the Readme.htm file before you install the driver. Updating the System Program Checking the version Check the version of the VS-100’s system software. When you power up the VS-100, the version of the current system software is displayed in the lower right of the screen. Version Description V1.30 or earlier An update is required. Perform the update as described below. V1.50 or later An update is not required. Updating 1. Switch on the VS-100’s power, and before the level meter screen appears, simultaneously press the compressor/equalizer setting button and the CH1 [COMP/EQ] button, and continue holding down these buttons until the following screen appears. The current system software version will appear. USB updater V1.30/01CA (current version) 2. Use the USB cable to connect the VS-100 to your computer. When the USB connection is detected, the following screen will appear. USB updater USB Online V1.30/01CA 3. Double-click “UpdSMFJ” on your computer. 4. In the “MIDI Out Device” field, choose “CONTROL (VS-100).” (on a Mac, choose “CONTROL.”) 5. Click the [Path] button (on a Mac, the [Select...] button), and in SMF Path (on a Mac, SMF Folder), specify the folder location that contains the update files (_00001.mid–_00008. mid, end.mid). 6. Click the [Scan SMF] (not required on a Mac), and verify that the update files (_00001.mid–_00008.mid, end.mid) are shown in the file list. 7. Click the [Send] button File transmission will begin. Transmission status is shown on the screen. USB updater 12345 (Status of transfer) USB Online V1.30/01CA When the transmission of the program has finished, the process of writing the program into the VS-100 will begin. NOTE Do not power off the VS-100 until the update is complete, doing so may damage the unit. A screen like the following will appear. USB updater erase USB Online V1.20/01AF USB updater write USB Online V1.20/01AF When the program has been updated successfully, a screen like the following will appear. USB updater Update Successfully Please Reboot V1.20/01AF -> V1.50/01D4 Verify that the updated version is displayed. This completes the update procedure. 8. Turn the power of the VS-100 off, then on again. Make sure that the system software version shown in the lower right of the screen is V1.50. * If the update was unsuccessful, you can retry the process from step 1. Updating the VS-100/VS-700 Updating the VS-700 Updating the VS-100/VS-700 Updating the VS-700 You’ll need to perform the following updates in order to use expanded I/O functionality. • Update the driver to version 2.00 or later. (Windows only) • Update the system program to version 1.30 or later. Updating the Driver You must install both the VS-700 driver and the VS-700C driver. * The VS-700C driver is required for updating the system program of the VS-700C console, so you must be sure to update the VS-700 driver and the VS-700C driver before you update the system program. * In order to update the driver for the VS-700C, you must set the VS-700C to the standalone mode. For details, refer to p. 164 in the owner's manual for the VS-700. The downloaded file is a zip format archive. Right-click the file icon, choose “Extract All” from the menu that app...