Évaluations - 2, GPA: 4
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
(Leaving the power cord connected while working can result in electric shock. Leaving other cables connected can interfere with work.) • Be careful not to drop any screws inside the instrument during installa- tion. (This can be prevented by keeping the optional units and cover away from the instrument while attaching). If this does happen, be sure to remove the screw(s) from inside the unit before turning the power on. Loose screws inside the instrument can cause improper operation or serious damage. If you are unable to retrieve a dropped screw, consult your Yamaha dealer for advice. • Install the optional units carefully as described in the procedure below. Improper installation can cause shorts which may result in irreparable damage and pose a fire hazard. • Do not disassemble, modify, or apply excessive force to board areas and connectors on optional units. Bending or tampering with boards and connectors may lead to electric shock, fire, or equipment failures. • It is recommended that you wear gloves to protect your hands from metallic projections on optional units and other components. Touching leads or connectors with bare hands may cause finger cuts, and may also result in poor electrical contact or electrostatic damage. • Be careful of static electricity. Static electricity discharge can damage the IC chips on the DIMM. Before you handle the optional DIMM, to reduce the possibility of static electricity, touch unpainted metal parts or a ground wire on the devices that are grounded. • Handle the optical units with care. Dropping or subjecting them to any kind of shock may cause damage or result in a malfunction. • Do not touch the exposed metal parts in the circuit board. Touching these parts may result in a faulty contact. • Be careful not to misplace any of the screws. • Do not use any screws other than what are installed on the instrument. Use of incorrect screws can cause damage. Compatible DIMMs WARNING CAUTION NOTICE DIMM Type and DIMM Configuration 64MB x 2 = 128MB 128MB x 2 = 256MB 256MB x 2 = 512MB Optional DIMM Installation Appendix 148 DTX900 Owner’s Manual 1 Turn the DTX900 power off, and discon- nect the power cord. 2 Turn over the DTX900 so you can have direct access to the underside. To protect the data dial and sliders from damage, place the DTX900 so the four corners are supported by something that provides sufficient support, such as magazines or cushions. Place supports at all four corners, taking care not to touch the Data dial and Sliders. 3 Remove the slot cover. Remove the screws from the slot cover by using a Phillips screwdriver. 4 Insert the two DIMMs into the DIMM sock- ets. Location for DIMM installation Installing the DIMM modules to the sockets 4-1 Press the ejector levers to the outside of the socket. 4-2 Insert the DIMM vertically in the socket. Press the DIMM in firmly until it “snaps” or locks in place. Confirm whether or not both the levers are firmly locked. DIMM Installation IMPORTANT Keep the removed screws in a safe place. They will be used when re-attaching the cover to the instru- ment after installing the DIMMs. Rear panelBottom surface of the DTX900 Slot cover Underside of the DTX900 DIMM slot x 2 Make sure that the DIMM module is aligned correctly before you install it. Ejector lever Notch for alignment Optional DIMM Installation Appendix DTX900 Owner’s Manual 149 Appendix 5 Re-install the cover you removed in step 3, in reverse order. 6 Check that the installed DIMMs are func- tioning properly. Set the DTX900 right-side up, and connect the AC power adaptor to the DC IN jack of the DTX900 and an AC wall out- let. Turn on the power, go to the Sampling mode by pressing the [SAMPLING] button, then press the [SF6] INF button (page Optional DIMM Installation Appendix DTX900 Owner’s Manual 149 Appendix 5 Re-install the cover you removed in step 3, in reverse order. 6 Check that the installed DIMMs are func- tioning properly. Set the DTX900 right-side up, and connect the AC power adaptor to the DC IN jack of the DTX900 and an AC wall out- let. Turn on the power, go to the Sampling mode by pressing the [SAMPLING] button, then press the [SF6] INF button (page priate available memory size is indicated in the display. 1 Press the ejector lever until the DIMM unlocks. 2 Pull the DIMM vertically out of the socket. NOTE • When you re-install the cover, make sure to steady the cover from the side with your hand. NOTE • If the DIMMs have not been installed properly, the Sampling function will not work correctly. If this occurs, turn the power off, perform the instructions above again, and make sure to install the DIMMs firmly. Memory size Removing DIMMs Appendix 150 DTX900 Owner’s Manual Troubleshooting No sound, even when the pad is hit. . Check whether or not the lamp of the TRIGGER INDICA- TOR lights when you hit the pad. If not, make sure the pads and Drum triggers (Yamaha DT20, etc.) are con- nected correctly to the input jacks of the DTX900. (page Appendix 150 DTX90...
Ce manuel est également adapté pour les modèles :Instruments de musique - DTX900K (2.76 mb)
Instruments de musique - DTX950K (2.76 mb)