Évaluations - 2, GPA: 4.5
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Doing so may result in deformation, discoloration, damage or deterioration. When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration. Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury. Continued on the next page (on the back side) Mounting the pads and the trigger module on the rack system Mount the pads and the trigger module on the rack system. Then position the kick pad and the hi-hat. Mounting the TP65 (Drum pads) on the rack system Figure 8: Pads Assembly-1 Figure 9: TP65 !1 Clamp bolt !2 TP65 (Rear side) 1 See Figure 9. Attach the clamp bolts (!1) on TP65s (!2). Tighten the clamp bolts fi ve to six turns each. Figure 10: Pads Assembly-2 2 See Figure 10. Loosen the knob (shown with ) of the tom holder on the middle left. Move the tom holder inward as shown in the close-up illustration (m). Then tighten the knob and attach the tom holder fi rmly at a position where it points slightly downward. Figure 11: Tom Holder and Drum Pad !3 Tom holder !4 Clamp bolt 3 Attach the TP65 (Drum pad) to the tom holder as shown in Figure 11. Tighten the clamp bolt and attach the drum pad TP65 fi rmly. 4 See Figure 10 again. Loosen the knob (shown with ) of the tom holder on the upper left. Move the tom holder inward as shown in the close-up illustration (n). Then tighten the knob and attach the tom holder fi rmly at a position where it points slightly downward. 5 Attach the TP65 (Drum pad) to the tom holder . Tighten the clamp bolt and attach the drum pad TP65 fi rmly. 6 Repeat step 4 and 5 in the same manner for tom holders and at the center of the rack system and for tom holder on the right, and attach the TP65 (Drum pad) to each tom holder. Mounting the PCY65 (Cymbal pads) on the rack system Figure 12: Pads Assembly-3 Figure 13: Cymbal holder-1 @1 Cymbal holder @2 Wing nut @3 Felt washer 1 See Figure 13. Remove the wing nut (@2) and one of the felt washers (@3) from the cymbal holder (@4). Figure 14: Cymbal holder-2 @4 PCY65 (Cymbal pad) 2 Attach the PCY65 (Cymbal pad) (@4) to the cymbal holder (@1) as shown in Figure 14. Attach the felt washer (@3) and the wing nut (@2) removed in step 1, and tighten it. Turn the wing nut until you are certain that the cymbal pad is attached. The cymbal pad is designed to shake when you hit the surface, even when the wing nut is tightened securely. Mounting the DTXPL (Trigger module) Figure 15: Pads Assembly-4 Figure 16: Module stand-1 @5 Module stand @6 Clamp 1 See Figure 16. Loosen the knob of the clamp (@6) (shown with ) and remove the module stand (@5) from the clamp (@6). Figure 17: Module stand-2 @7 Fastening screw* @8 DTXPL (Rear side) * Th e fastening screws are included in the same plastic bag that includes the Assembly Manual of rack system RS40. Th e plastic bag is packaged between the space within the cardboards used for cushioning. 2 Tighten the fastening screws (@7) with a Phillips screwdriver, as shown in Figure 17, to attach the module stand (@5) onto the rear side of the trigger module (@8). Figure 18: Module stand and clamp @9 DTXPL + Module stand #0 Clamp #1 Knob 3 Attach the module stand (@9) onto the clamp (#0). Tighten the knob (#1) and fi x the position. Assembling the KP65 (Kick pad) 1 If a drum mat (sold separately) is not available, lay a cardboard on the fl oor to prevent scratching the surface. Figure 19: KP65 Assembly #3 Body #4 Base #5 Wing bolt #6 Spring washer #7 Washer 2 Remove the wing bolt (#5), the spring washer (#6) and the washer (#7) from the body (#3), and keep the four sets nearby in the order removed. * If the wing bolt, the spring washer and/or the washer are separated from each other, set them as illustrated in Figure 19-(a). 3 Set the base (#4) on the body (#3), and attach them using the wing bolt, the spring washer and the washer removed in step 2. Assembling the FP6110A (Foot pedal) 1 If a drum mat (sold separately) is not available, lay a cardboard on the fl oor to prevent scratching the surface. Figure 20: FP6110A Assembly $1 Beater $2 Beater locking bolt $3 Radius rod $4 Drum key 2 Insert the radius rod ($3) into the hole of the frame as shown in Figure 20. 3 Insert the beater ($1) into the hole of the beater attachment part until the further end of the beater slides outward about 15 mm. Tighten the beater locking bolt ($2) using the drum key ($4). Attaching the FP6110A (Foot pedal) to KP65 (Kick pad) Figure 21: FP6110A and KP65 Figure 22: T-handlet bolt %1 FP6110A (Foot pedal) %2 KP65 (Kick pad) %3 T-handlet ...
Ce manuel est également adapté pour les modèles :Instruments de musique - DTXPL (686.49 kb)