Évaluations - 2, GPA: 3
(
)
)
|
Facilité d'utilisation
• The TV remote control signal transmission function is enabled even if the unit is in standby mode. Operate the unit by TV remote control (TV remote control learning function) You can use the TV remote control solely to operate by having the unit learn the TV remote control operations. You can operate the following functions by TV remote control. • Volume down • Volume up • Power on/standby mode y Some TV remote controls may not control these functions. Use the remote control supplied with the unit in this case. 1 Set the unit and TV to standby mode. 2 Press both the INPUT button and button of the main unit, release the button first, then release the INPUT button. The unit enters the remote control learning mode. Flashes in red Continued to the next page. \ English 9 En Additional Information 3 Press the button below of the main unit to select the operation you want the unit to learn. Operation you want the unit to learn The button of the unit The Indicator flashes in green Volume down VOLUME – Volume up VOLUME + Power on/standby mode 4 Point your TV remote control at the remote control sensor and press the respective button twice or three times until the indicator changes from flashing green to lit green. Press (1 sec) Release (1 sec) Press (1 sec) Flashes rapidly Indicator Approx. 30 cm (1 ft) Flashes Flashes rapidly Success in learning e.g. Volume up Fault in learning The UNIVOLUME, CLEAR VOICE and SURROUND indicators flash in green simultaneously for about 3 seconds. 5 Repeat steps 3 and 4 to make the unit learn the other operations. 6 Press the button of the main unit for more than 3 seconds to finish the remote control learning mode. Release the button of the main unit when all the indicators light up in green. The unit enters standby mode. Notes • The unit will automatically set to standby mode if the unit in the remote control learning mode is left turned on for 5 minutes without any operation being performed. • If learning fails, try again with your TV turned off. Note that screen glare may disturb TV remote control learning. Removing all learned TV remote control operations 1 Set the unit to standby mode. 2 Press both the INPUT button and button of the main unit, release the button first, then release the INPUT button. Flashes in red 3 Press the INPUT button of the main unit again for more than 3 seconds. 4 Release the INPUT button of the main unit when qD DTS indicator flashes. Press the button of the main unit for more than 3 seconds to finish the remote control learning mode, or to have the unit learn operations of another TV remote control. Resetting the unit Should the unit freeze for any reason, this may be remedied by initiating the factory settings. 1 Set the unit to standby mode. 2 Press and hold the button of the main unit for more than 3 seconds. All the indicator flashes in green. 3 Release the button of the main unit. 10 En English Immediately after turning on the unit, the indicators show the state of the unit as below. The indicators show the setting mode as below. Operation indicators of the unit The six indicators are placed in the above order, and their color and appearance are symbolically represented as below. : Lights up in green : Lights up in red : Lights up in orange : No light : Flashes in green : Flashes in red Indication immediately after turning on the unit Playback of the subwoofer ( English Immediately after turning on the unit, the indicators show the state of the unit as below. The indicators show the setting mode as below. Operation indicators of the unit The six indicators are placed in the above order, and their color and appearance are symbolically represented as below. : Lights up in green : Lights up in red : Lights up in orange : No light : Flashes in green : Flashes in red Indication immediately after turning on the unit Playback of the subwoofer (.P. 8) TV remote control signal transmission function (.P. 9) Indicators Built-in subwoofer Off External subwoofer Off Built-in subwoofer On External subwoofer On Indication of the setting mode Setting mode Indicators Audio delay control (.P. 8) * TV remote control learning (.P. 9) * * These indicators light up according to the state. Normal indication INPUT : TV : BD/DVD : STB : Stand-by SURROUND : Surround playback :Stereo playback CLEAR VOICE : Clear voice on : Clear voice off : Mute UNIVOLUME : UniVolume on : UniVolume off qD DTS : Dolby Digital : PCM : DTS Digital Surround qPL II : Surround playback of 2ch stereo signal input : •Stereo playback • Surround playback of surround signal input 11 En Troubleshooting Troubleshooting Refer to the chart below should the unit not function properly. If the problem you are experiencing is not listed below, or if the instruction below does not help, set the unit to the standby mode, disconnect the AC power supply cable, and contact the nearest authorized Yamaha dealer or service center. Check the below first. 1 The AC power supply cable of the unit, TV and external compon...
Ce manuel est également adapté pour les modèles :Instruments de musique - YAS-101 (3.39 mb)