Évaluations - 2, GPA: 3
(
)
)
|
Photos et spécifications Yamaha NS-45E |
Facilité d'utilisation
c Do not sit on or set objects on top of the speaker. Vibrations or jolts associated with earthquakes and other phenomena or activities may cause the speaker to fall over. For safety reasons, using commercially available products that increase stability in the speaker is recommended (metal fittings or chains, etc.). Use the stands included with the speakers to increase stability: Be sure to use the stands regardless of where the speakers are positioned. Attaching the stands included with the speakers reinforces the base of the speaker not to fall over. Please be cautioned that even though the stands are connected, this does not guarantee that the speakers will not fall over. SPECIFICATIONS REMOVING THE FRONT COVER The front cover is fixed to the cabinet at six points, and can be removed if desired. To remove the cover, hold both sides and slowly pull straight away from the speaker. To reattach, line up the six pegs on the inside surface of the cover with the six corresponding holes on the speaker and push gently. Note When the cover is removed, take care not to touch the speaker units with your hands or to exert excessive force with tools. Type........................2-way 3-speaker bass-reflex speaker system Driver ........................................................16 cm cone woofer x 2 3 cm dome tweeter Input Terminal ..............................................................Screw-type Impedance...........................................................................6 ohm Frequency Response............................................38 Hz – 30 kHz Nominal Input Power..............................................................80W Maximum Input Power..........................................................240W Sensitivity (2.83V, 1m) .........................................................90 dB Crossover Frequency ...........................................................3 kHz Dimensions (WxHxD) ...................................233 x 880 x 275 mm (9-3/16” x 34-5/8” x 10-13/16”) Weight.........................................................11.6 kg (25 lbs. 8 oz.) Accessories ...............................................Speaker cord (4m) x 2 Stand x 8 Screw x 16 Leg x 8 * Specifications subject to change without notice due to product improvements. * Care should be taken not to exceed the input power values noted above. CONNECTION TO YOUR AMPLIFIER BEFORE MAKING CONNECTIONS, MAKE SURE THAT THE AMPLIFIER IS SWITCHED OFF. n CONNECTIONS c Connect the screw-type input terminals at the rear of the speakers to the speaker output terminals of your amplifier with the provided speaker cords. c One side of the speaker cord is red and the other side is black. Connect the (+) terminals on both the amplifier and the speakers using this red side. Connect the (–) terminals on both components using the black side of the cord. c Connect one speaker to the left (marked L) terminals of your amplifier, and another speaker to the right (marked R) terminals, making sure not to reverse the polarity (+, –). If one speaker is connected with reversed polarity, the sound will be unnatural and lack bass. Procedure: 1 Loosen the terminal knob. 2 Insert the bare speaker wire end properly into the terminal hole. [Remove approx. 10 mm (3/8”) insulation from the speaker cord.] 3 Tighten the knob. 4 Test the security of the connection by pulling lightly the cord at the terminal. ATTACHING THE STANDS Stand x 8 Screw x 16 Leg x 8 When placing the speakers, be sure to use the stands to increase stability. Use the 8 specified holes located on the base of the speaker. Procedure: 1 Put a screw through the inside hole on the stand, and screw it into the speaker at one of the outside holes on the base of the speaker. At this time, screw it untightly so that the stand can still be moved. 2 Put another screw through the outside hole on the stand, and screw it into the inside hole on the base of the speaker. 3 Tighten both of the screws firmly. 4 Attach a leg to the bottom of the end portion of the stand. 5 Attach the other stands to the other corners of the base of the speaker in the same way and confirm that all 4 stands have been firmly attached. Note Be carefull not to apply force to the side of the speaker, otherwise the speaker may fall causing damage to the speaker or personal injury. Speaker (L) Speaker (R) Speaker output terminals of the amplifier Loosen Black (–) Tighten Red (+) Red Amplifier Note Do not let the bare speaker wires touch each other as this could damage the speakers or the amplifier, or both of them. PLACING THE SPEAKERS c Place the speakers on a sturdy vibration-free surface. If you cannot obtain good bass quality when the speakers are placed directly on the floor, insert a block etc. between the speakers and the floor. c Better stereo images will be obtained when the speakers are slightly angled in towards the listeners. Note Bacause these speakers are not a magnetically shielded type, there may be some inf...