Évaluations - 4, GPA: 4.3
(
)
)
|
Facilité d'utilisation
The parameters of a MIX channel for which this LED is lit will not change even if a scene memory is recalled. Recall Safe settings can be made in the SELECTED OUTPUT CHANNEL bolck or display (SCENE function RECALL SAFE screen). 6MIX [MUTE SAFE] LED This LED will light for MIX channels that are set to Mute Safe (a state in which the channel will be unaffected by mute group operations). A MIX channel for which this LED is lit will be unaffected even if a mute group to which it belongs is muted. Mute Safe settings can be made in the SELECTED OUTPUT CHANNEL block or display (OUT DCA/ MUTE function MUTE GROUP ASSIGN screen). 7MIX [DCA] switch and LEDs This switch assigns the MIX channel to DCA groups 9–12. When the MIX channel is assigned to a DCA group, the corresponding LED will light. Hint You can assign a single MIX channel to multiple DCA groups, and assign multiple MIX channels to a single DCA group. MIX OUTPUT block MIX OUTPUT block ] Assigning a MIX channel to a DCA group 1. In the DCA GROUP block, press one of the [ASSIGN DCA] switches 9–12 to select a DCA group (9–12). 2. In the MIX OUTPUT block, press the MIX [DCA] switch of the MIX channel that you wish to assign to the above-selected DCA group. The LED for that DCA group will light. • DCA groups 9–12 can be used for either input channels or output channels. However, it is not possible to assign both inputs and outputs to the same DCA group. For this reason, if an input channel is already assigned to DCA group 9–12, attempting to assign an output channel will cause a message to be displayed, and you will not be able to do so. • When a scene is recalled, the DCA group data of recall safe channels may be adjusted so that recall safe settings are consistent within DCA groups 9–12. Also when a channel library is recalled, the data recalled to a channel may be adjusted so that settings are consistent within DCA groups 9–12. 8MIX [PAIR] LED This LED will light if pairing has been selected for two adjacent odd and even-numbered channels (MIX channels 1/2, 3/4, ...) of MIX channels 1–48. Pairing of MIX channels can be set/defeated using the MIX [SEL] switches (B), and in the display (PAN ROUTING function, etc.). 9MIX [LEVEL/BAL] encoder and LEDs This encoder sets the output level of the MIX channel 1–48 (the level of the signal that is sent to the output unit patched to that MIX channel) The range is from – . – +10 dB, and the approxi mate current value is shown by the perimeter LEDs. The LED at the ® mark will light to indicate nominal level (0 dB). If two adjacent odd and even-numbered MIX channels are paired, the right (even-numbered) encoder will function as the MIX [LEVEL] encoder to set the common output level of the two channels, and the left (odd-numbered) encoder will function as the MIX [BAL] encoder to set the volume balance between the two channels. In this case as well, the approximate current value is shown by the perimeter LEDs. Of the LEDs around the [BAL] encoder, the LED at the q mark will light to indicate that the left/right balance is equal. • When MIX channels are not paired PAIR ON ON MIX 1 MIX 2 OUTPUT OUTPUT LEVEL LEVEL MIX CHANNEL OUTPUT LEVEL OUTPUT PATCH ON ON MIX 1 MIX 2 OUTPUT LEVEL CS1D Reference Manual (Hardware) CS1D Reference Manual (Hardware) When MIX channels are paired PAIR ON ON OUTPUT LEVEL BALANCE OUTPUT PATCH MIX CHANNEL ONMIX 1 MIX 2 MIX 1/2 BALANCE MIX 1/2 OUTPUT LEVEL 0MIX [INS] LED This LED indicates the insertion status of the MIX channel. When insertion is on, the switch LED will light, and the insert out/in point specified in the display (OUTPUT PATCH function INSERT PATCH screen) will be enabled. AMIX [CUE] switch and LED This switch monitors the currently selected MIX channel. When this switch is pressed, the PFL (pre-fader listen) or POST ON (after the [ON] switch) signal of the corresponding MIX channel will be sent to the CUE bus, and can be monitored from the CUE OUT jacks, MONITOR OUT jacks A, or PHONES jack. The location of the signal that is sent to the CUE bus and the monitoring method can be switched from the console in the MASTER block CUE section, or in the display (MON/CUE function CUE/SOLO screen). BMIX [SEL] switch and LED This switch selects the MIX channel that your opera tions will affect. The MIX [SEL] LED of the currently selected MIX channel will light. The MIX channel selected by this switch can be controlled in the SELECTED OUTPUT CHANNEL block. It will also be reflected by the settings in the display. Hint If the selected MIX channel is paired, the MIX [SEL] LED of the other MIX channel of the pair will blink. You can also use the MIX [SEL] switches to set/defeat pairing. The MIX channel shown by the INPUT block MIX SEND [NAME] indicator and the MIX SEND [NUMBER] indicator will also follow the operation of the MIX [SEL] switch. (However, INPUT blocks whose [LOCAL] LED is lit are excepted.) [Procedure] Using the MIX [SEL] switches to set/defeat pairing of MIX channels 1. For adjacent odd...