.HA GAIN/O/HPF 1 32 AHA (HA Gain) Adjusts the gain of the internal head amp or of the external head amp (AD8HR) patched to the input channel. The current value is shown in the numerical box below the knob. You can set this to the default value (+10 dB) by holding down the key and clicking the knob. You can also use the [48V] button to switch phantom power on/off. BO (Phase) Inverts the phase of the signal after AD conversion. CHPF (High Pass Filter) Use the [ON] button at the right to switch the high-pass filter on/off. You can use the knob at left to adjust the cutoff frequency. The current value is shown in the numerical box below the knob. An indication of “H” will appear on the EQ graph of the equalizer. M7CL V2 Editor Owner’s Manual 25 .. Here you can specify how the signal will be sent from the input channel to the STEREO bus / MONO bus. MODE • ST/MONO button When this button is on, the signal will be sent to the STEREO L/R bus and independently to the MONO bus. [INPUT CH 1–48] [ST IN channel 1–4] PAN (BALANCE for ST IN) Adjusts the panning of the signal sent from the input channel to the STEREO bus L/R channels. You can set this to the center position by holding down the key of the computer keyboard and clicking the knob. This is linked with the [PAN] encoder in the SELECTED CHANNEL section of the M7CL panel. ST Switches the signal sent from the input channel to the STEREO bus on/off. M(C) Switches the signal sent from the input channel to the MONO bus on/off. • LCR button When this button is on, the signal will be sent to the L/C/R buses which work in conjunction with each other. [INPUT CH 1–48] [ST IN channel 1–4] PAN (BALANCE for ST IN) Adjusts the panning of the signal that is sent from the input channel to each of the L/C/R channels.You can set this to the center position by holding down the key of the computer keyboard and clicking the knob. This is linked with the [PAN] encoder in the SELECTED CHANNEL section of the M7CL panel. CSR (Center Side Ratio) Adjusts the proportion of the CENTER channel level relative to the STEREO bus L/R in a range of 0–100%. M7CL V2 Editor Owner’s Manual 26 ..R 4 7 8 9 21 3 6 5 KJ ALIBRARY Accesses the INPUT EQ page of the LIBRARY window. BON Switches the EQ on/off. CEQ graph Indicates the response for the EQ of the currently selected channel. To reset the EQ to flat response, hold down the key of your computer keyboard and click the graph (The HPF setting will remain). DQ EFREQUENCY FGAIN These knobs adjust the Q, center frequency, and boost/cut amount for the four bands LOW, LO-MID, HI-MID, and HIGH. G HIGH shelving If this button is on, the HIGH EQ will be switched to a shelving type (the Q knob of the HIGH EQ will disappear). H LPF (Low Pass Filter) If this button is on, the HIGH EQ will function as a low pass filter. The Q knob of the HIGH EQ will disappear, and the GAIN knob will act as the low pass filter on/off switch. LOW shelving If this button is on, the LOW EQ will be switched to a shelving type (the Q knob of the LOW EQ will disappear). JTYPE I/TYPE II (EQ type) Selects either TYPE I (the algorithm used by previous digital mixers) or TYPE II (a newly developed algorithm) as the EQ type. M7CL V2 Editor Owner’s Manual 27 KATT (Attenuation) KATT (Attenuation) .DYNAMICS1/2 You can select one of the following types for each of the two dynamics processors. DYNAMICS1: GATE, DUCKING, EXPANDER, COMPRESSOR DYNAMICS2: COMPRESSOR, COMPANDER-H, COMPANDER-S, DE-ESSER If GATE/DUCKING is selected L 4 J 7 8 6 9 K 1 2 35 M ATYPE Indicates the type of the currently selected gate. You can click here to select the type. BLIBRARY This button accesses the dynamics library. Clicking this button will open the DYNAMICS page of the LIBRARY window. CON This button switches the gate on/off. DResponse curve Indicates the response for the gate of the currently selected channel. EGR meter This meter indicates the amount of gain reduction. FTHRESHOLD (Threshold level) Specifies the level at which the gate will open and close. The gate will open when the key-in signal exceeds this level, and will close when the signal falls below this level. GRANGE Specifies the amount by which the signal is attenuated while the gate is closed. HDECAY Specifies the time over which the gate will close after the hold time has elapsed. IATTACK Specifies the time from when the key-in signal exceeds the threshold level until the gate opens. M7CL V2 Editor Owner’s Manual 28 JHOLD JHOLD KKEY IN SOURCE Click this to select one of the following signals to use as the key-in source. SELF PRE EQ The pre-EQ signal of the currently selected input channel SELF POST EQ The post-EQ signal of the currently selected input channel MIX OUT 13–16 The output signal of the corresponding MIX channel immediately before the output attenuation CH 1–48 POST EQ The post-EQ signal of the corresponding input channel (however, you can only choose channels belonging to the same group, within the seven groups...
)
