Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
These knobs should generally be set close to the “Ў” position. These controls send either the signal from immediately prior to the channel fader (pre-fader signal) or the signal after the channel fader (post-fader signal) to the corresponding buses. The types of signals sent by the AUX and EFFECT controls on each mixer model are as follows: • MG206C AUX1: Pre-fader AUX2, 3: Pre-fader/post-fader (determined by the AUX PRE switch B) AUX4: Post-fader • MG166CX AUX1: Pre-fader AUX2: Pre-fader/post-fader (determined by the AUX PRE switch B) EFFECT: Post-fader • MG166C AUX1: Pre-fader AUX2: Pre-fader/post-fader (determines by the AUX PRE switch B) AUX3: Post-fader NOTE •To send the signal to the STEREO bus engage the ON switch ( ). • On stereo channels, the L (odd) and R (even) input signals are mixed and sent to the AUX and EFFECT buses. BAUX PRE Switch Selects whether the pre-fader or the post-fader signal is fed to the AUX buses. If the switch is on ( ), the mixer sends the pre-fader signal to the AUX buses, so that AUX outputs are not affected by the channel fader I. If the switch is off ( ) the mixer sends the post-fader signal to the AUX buses. CPAN Control PAN/BAL Control BAL Control The PAN control determines the stereo positioning of the channel signal on the GROUP 1/2 and GROUP 3/4 buses or on the STEREO L/R bus. The BAL control knob sets the balance between left and right channels. Signals input to the L input (odd channel) go to the GROUP 1 or 3 buses or to the STEREO L bus; signals input to the R input (even channel) go to the GROUP 2 or 4 buses or the STEREO R bus. NOTE On channels where this knob provides both PAN and BAL control, the knob operates as a PAN control when input is received via the MIC jack or L (MONO) input only, and as a BAL control when input is received via both L and R inputs. DON Switch Turn this switch on to send the signal to the buses. The switch lights orange when on. EPFL (Pre-Fader Listen) Switch This switch lets you monitor the channel’s pre-fader signal. Press the switch in ( ) so that it lights to turn it on. When the switch is on the channel pre-fader signal is output to the PHONES and MONITOR OUT jacks for monitoring. F1-2 Switch This switch assigns the channel’s signal to the GROUP 1/2 bus. NOTE To send the signal to the GROUP 1/2 bus turn the ON switch on ( ). G3-4 Switch This switch assigns the channel’s signal to the GROUP 3/4 bus. NOTE To send the signal to the GROUP 3/4 bus turn the ON switch on ( ). HST Switch This switch assigns the channel’s signal to the STEREO L/R bus. NOTE To send the signal to the STEREO bus turn the ON switch on ( ). IChannel Fader Adjusts the level of the channel signal. Use these faders to adjust the balance between the various channels. NOTE Set the fader sliders for unused channels all the way down to minimize noise. 14 MG206C/MG166CX/MG166C Owner’s Manual Reference Front & Rear Panels Reference Front & Rear Panels * Only the MG166CX has digital effects. 23456784 3 5 0 2 6 1 7 8 9 1FOOT SWITCH Jack A Yamaha FC5 foot switch (sold separately) can be connected to this jack and used to toggle the digital effects ON and OFF. PROGRAM Dial Selects one of the 16 internal effects. See page 19 for details about the internal effects. PARAMETER Control Adjusts the parameter (depth, speed, etc.) for the selected effect. The last value used with each effect type is saved. NOTE When you change to a different effect type, the mixer automatically restores the value that was previously used with that type (regardless of the current position of the PARAMETER knob). These parameter values are reset when the power is turned off. AUX Control Adjusts the level of the signal sent from the internal digital effect unit to the AUX buses. NOTE The signal level sent to the AUX buses is not affected by the EFFECT RTN fader. ON Switch Switches the internal effect on or off. The internal effect is applied only if this switch is turned on. The switch lights orange when on. An optional Yamaha FC5 foot switch (sold separately) can be used to toggle the digital effects ON and OFF. NOTE The ON switch lights and the internal effect unit is active when the power is initially turned on. PFL Switch Turn this switch on to send the effect signal to the PFL bus. 1-2 Switch This switch assigns the effect signal to the GROUP 1/2 bus. 3-4 Switch This switch assigns the effect signal to the GROUP 3/4 bus. 9ST Switch This switch assigns the effect signal to the STEREO L/R bus. 0EFFECT RTN Fader Adjusts the signal level sent from the internal digital effect unit to the STEREO bus. MG206C/MG166CX/MG166C Owner’s Manual 15 Front & Rear Panels MG206C/MG166CX/MG166C Owner’s Manual Reference 16 Master Control Section 0 A I G D E C 9 B 6 8 7 1 2 3 4 5 H F 0 A I G E 9 B H F 6 8 4 1 3 7 5 2 D C Rear panel . MG206C . MG166CX/MG166C * 1, C MG166C : EFFECT > AUX3 Reference Front & Rear Panels Reference Front & Rear Panels These impedance balanced* TRS phone jacks output the signals from the AUX...
Ce manuel est également adapté pour les modèles :Instruments de musique - MG166C (2.39 mb)
Instruments de musique - MG206C (2.39 mb)