Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
The gain control should be set so that the indicator flashes occasionally or does not light at all during normal playing. PRE-SHAPE CONTROL: This is a pre-EQ "master" tone control. With the control set at "12 o'clock", the signal will pass to the EQ section "flat” |with no modification of tone). As the control is turned clockwise, high frequencies will be boosted and as the control is turned counterclockwise, low frequencies will be boosted. This control can be used to "dial in" a general tone setting which can be fine tuned by the EQ section or to instantly modify an existing EQ setting with one knob. EQUALIZATION SECTION 6. LOW BOOST SWITCH: Low frequencies are boosted when this switch is depressed. 7. GRAPHIC EQUALIZER: This is the main tone control section of the B160XL. Seven bands of frequencies from 50 Hz to 5 kHz may be boosted by moving the sliders up or cut by moving the sliders down. The lower frequencies are to the left and the higher frequencies are to the right. A great many tone variations are possible using different settings of these sliders. 8. HIGH BOOST SWITCH: This switch adds additional high frequency boost such as desired for a "popping" or "slapping" playing style. 9. MASTER VOLUME CONTROL: This control sets the overall listening level of the B160XL. 10. LIMIT LED INDICATOR: The B160XL contains a power amp limiter which automatically limits the signal to the power amp to a point just below "clipping" or distortion. This is to assure a clean undistorted sound at full power. The limit LED indicator will be lit whenever full power is reached. EFFECTS LOOP 11. EFFECTS LOOP OUTPUT: This jack may be connected to the line level input of an external effects device. This jack may also be used as a "direct" unbalanced send for recording, etc. 12. EFFECTS LOOP INPUT: This jack may be connected to the line level output of an external effects device. This "Post Gain" configuration is helpful in obtaining optimum input signal levels to external devices and reducing the noise levels associated with them. CHORUS SECTION 13. CHORUS SWITCH: The chorus effect is turned on when this switch is depressed. 14. SPECTRUM CONTROL: With this control fully counterclockwise the full frequency spectrum of the signal is chorused. As the control is turned clockwise low frequencies are allowed to pass with no chorus effect allowing a more "tight" or punchy low end sound with upper harmonic chorusing. This is usually desirable when playing in a "live" situation. 15. DEPTH CONTROL: This control is used to set the "depth" or amount of chorus effect. 16. RATE CONTROL: This control is used to set the rate of chorusing. This control when used in conjunction with the Depth control allows a wide range of chorus effects from a subtle chorus effect to far out sound effects. 17. LINE OUT LEVEL CONTROL: This control is used to set the level of the balanced line output jack. 18. BALANCED LINE OUTPUT JACK: This jack provides a balanced output signal for connection to an external power amp, tape deck, or mixing board. 19. ON/OFF LED INDICATOR: The LED will be lit when the amplifier is turned on. 20. POWER SWITCH: Pushing the switch to the up position turns the B160XL on. REAR PANEL FEATURES AND FUNCTIONS 21. LINE OUTPUT JACK: This jack pro vides a high impedance unbalanced output for connecting the B160XL to another amplifier or tape recorder. Simply run a cord from this jack to the input of another amplifier or tape deck. 22. LINE INPUT JACK: This jack is used as a direct input to the power amp. Plugging into this jack disconnects the 47-535-05 direct (normal) connection between the preamp and power amp. The Line Input Jack may be used with the Line Output Jack as an effects loop. 23&24 SPEAKER OUTPUT JACKS: Any load equal to at least 2 ohms may be connected to the speaker jacks. If more than one jack is used, the total load considering both jacks must be at least 2 ohms. The standard internal speaker configuration is equal to 4 ohms. This means that an additional 4 ohm load may also be connected , which would be a total of 2 ohms. 25. POWER CORD: Your BI60XL is equipped with a heavy-duty grounded three-wire power cord. Be sure this cord is properly plugged into a safely wired grounded 120 Vac 60 Hz AC power outlet before use. (If your B160XL was purchased outside the United States, refer to the rear panel for power ratings). For your safety, never attempt to defeat the ground connection on this cord. B-160XL TECHNICAL SPECIFICATIONS Output Power Rating 160 watts RMS 5% THD 4 ohm load-120Vac line Speaker Size and Rating B-160XL— 15" with 2-112" voice coil, 56 oz. magnet crate special design. B-160XLE— 15" Electro Voice Force Pre-Shape Control 14 dB boost @5 kHz 10 dB boost @ 50 Hz Low Boost Switch 10 dB boost @ 40 Hz Graphic Equalizer 24 dB range @ 50Hz, 100Hz, 200Hz, 400Hz, 800Hz, 1.6kHz, and 5kHz High Boost Switch 8 dB boost @ 10kHz Input Impedance 220k ohms Maximum Signal Level Accepted...