Évaluations - 4, GPA: 5
(
)
)
|
Facilité d'utilisation
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOIS- TURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. "IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL" “ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.” "REFERREZ-VOUS AU MANUAL D'UTILISATION" EXPLANATION OF GRAPHICAL SYMBOLS: EXPLICACION DE SIMBOLOS GRAFICOS: EXPLICATION DES SYMBOLES GRAPHIQUES: "DANGEROUS VOLTAGE" “VOLTAJE PELIGROSO” "DANGER HAUTE TENSION" = = PRECAUCION RIESGO DE CORRIENTAZO NO ABRA PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS O DESCARGAS ELECTRICAS, NO PERMITA QUE ESTE APARATO QUEDE EXPUESTO A LA LLUVIA O LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO. NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS. ATTENTION RISQUE D'ELECTROCUTION NE PAS OUVRIR ATTENTION: PROTEGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITE AFIN D'EVITER TOUT RISQUE D'INCENDIE OU D'ELECTROCUTION. POUR REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE. FXT30 Guitar Amp with Digital Signal Processing FXT30 Guitar Amp with Digital Signal Processing The Front Panel: 1 2 3 4 5 6 7 8 9 1010 1111 1212 1313 1: INPUT: Use this 1/4” jack to connect your guitar to the amplifier by means of a shielded instrument cable. SOLO CHANNEL: A high gain channel giving you sounds from a slight edge to serious overdrive. 2: GAIN: Use this control to adjust the amount of distortion for the Solo channel. 3: SHAPE: Use this control to adjust the tone of the Solo channel. 4: LEVEL: Use this control to adjust the output level of the Solo channel. 5: SOLO/CLEAN: Use this switch to select the Solo or Clean channel. With the switch in the out position, the Clean channel is selected. When the switch is depressed, the Solo channel is selected. CLEAN CHANNEL: A normal gain channel designed to give you crystal clear sounds to medium distortion. 6: VOL: Use this control to adjust the output level of the Clean channel. 7: LOW: Use this control to adjust the low frequency level of the clean channel. 8: MID: Use this control to adjust the midrange frequency level of the clean channel. 9: HIGH: Use this control to adjust the high frequency level of the clean channel. 10: DSP LEVEL: Use this control to adjust the level of the selected digital effect. The DSP effects can be turned on and off by using a footswitch (#16, rear panel). 11: DSP MODE: Use this control to select one of the 16 built-in digital effects. The numbers around the control correspond to the digital effects as listed in the chart below. The Digital Effects: 12: HEADPHONES: Use this jack to connect headphones to the amplifier. The internal speaker is disconnected when headphones are used. CAUTION: To avoid possible damage to your hearing, do not use headphones for extended periods of time at extremely loud levels. 13: POWER: Use this switch to turn the amplifier on (top of the switch depressed) and off (bottom of the switch depressed). The switch illuminates when the amplifier is turned on. The Rear Panel (not shown): 14: EXTENSION SPEAKER: Use this jack to connect the amplifier to an external speaker. The internal speaker is disconnected when this jack is used. The impedance of the external speaker must be 4 ohms or greater. WARNING: Do not attempt to use headphones in the Speaker jack! Permanent hearing damage could result! 15: FOOTSWITCH: Use this jack to connect the 1/4” stereo plug on the cable of a two-button footswitch (such as the Crate CFP2). This allows you to remotely switch between the Clean and Solo channels and turn the DSP effects on and off. 16: POWER CORD: The grounded power cord should only be plugged into a grounded power outlet that meets all applicable electrical codes and is compatible with the voltage, power, and frequency requirements stated on the rear panel. Do not attempt to defeat the safety ground connection. 1 -Small Room Reverb 9 -Flange with Reverb and Delay 2 -Medium Room Reverb 10 - Slow Tremolo Chorus With Reverb 3 -Large Room Reverb 11 - Chorus with Reverb and Delay 4 -Concert Hall Reverb 12 - Rotating Speaker 5 -Short Slapback with Small Room Reverb 13 - Octave Divider 6 -Medium Delay with Plate Reverb 14 - Touch Wah 7 -Long Delay with Large Room Reverb 15 - Inverse Wah 8 -Slow Deep Flange with Reverb 16 - Doubler FXT30 Guitar Amp with Digital Signal Processing FXT30 Guitar Amp with Digital Signal Processing FXT30 TECHNICAL SPECIFICATIONS: Output Power Rating >30W RMS @ 5% THD, 4., 120 VAC Gain Solo Ch 98dB +/-6dB @ 1kHz Clean Ch 42dB +/-6dB @ 1kHz Maximum Input Signal Accepted 6 volts peak-to-peak min. @ 1kHz Tone Controls Low 20dB range @ 80Hz Mid 12dB range @ 900Hz High 18dB range @ 10kHz S...