Évaluations - 5, GPA: 3.6
(
)
)
|
Facilité d'utilisation
as ^ AU^idí^í * ” Vjcifi? « Z. * Чл? ’"’tP-v;^ <> : - ^mot ¿VT VÍC$*%5# ?ЗД£ l'-lw. ‘.' •; -r^-\v¡ j5>V ENGLISH Thank you for selecting the KB/A™ 100 keyboard/acoustic amplification system! Once again, Peavey engineers have listened to input from keyboard players and put together a system that combines excellent features and sound in a portable, stylish package. The new KB/A™ series amplifiers also deliver awesome sound for drum machines and acoustic instruments. From thundering bass to crystal highs, it’s all there. For the full scoop, check out the features below. FRONT PANEL FEATURES CHANNEL ONE: LOW-Z INPUT (1) For use with low-impedance microphones or low-level sources equipped with a male XLR connector. HIGH-Z INPUT (2) For use with high-impedance microphones or high-level sources equipped with a 1/4" phone plug. MIC LEVEL (3) Controls the microphone’s input level. CHANNEL TWO: HIGH-Z INPUT (4) A1/4" phone jack input is provided with extremely “wide” dynamic range. This input will accept very high-level signals generated by synthesized keyboard systems or very low signals generated by practice or home keyboard units. This input is also for acoustic guitars and can be muted with a footswitch (optional). GAIN SWITCH (5) Boosts the gain of its channel by 12 dB. Depress to the “in” position to activate. LEVEL (6) Controls the Channel Two V4a phone jack input level. CHANNEL THREE: HIGH-Z INPUT (7) A!/" phone jack input is provided with extremely “wide” dynamic range. This input will accept very high-level signals generated by synthesized keyboard systems or very low signals generated by practice or home keyboard units. 3 GAIN SWITCH (8) Boosts the gain of its channel by 12 dB. Depress to the “in” position to activate. LEVEL (9) Controls the Channel Three V" phone jack input level. PRE EQ PATCH: SEND/RETURN JACK (10) A stereo out/in jack allows the uses of various auxiliary units (chorus, flanging, tape/digital/analog delays, equalizers, etc.) in line before the Equalization section. To utilize this system, a stereo plug (tip/ring/sleeve) to a “Y” cord must be used. The tip portion of the 1/4" stereo jack serves as the signal send (output), while the ring portion will return the processed signal to the system. The sleeve portion serves as the ground. The Pre EQ patch affects ail three channels. Since this is a stereo jack configuration, the first click on the jack may be used as a Pre EQ output with a mono V” plug if desired. This first click will not disturb the signal flow to the remainder of the system as it is fed into the EQ section. Note: IF THE SECOND CLICK OF THE OUT/IN JACK IS UTILIZED WITHOUT RETURNING ANY SIGNAL TO THE SYSTEM FROM AN EFFECTS DEVICE, THE REMAINING PREAMP FUNCTIONS WILL BE DISABLED. EQUALIZATION: LOW EQ (11) An active tone control (Shelving type, ±15 dB) that varies the low frequency range. Caution: Excessive low frequency boost causes greater power consumption and increases possibility of speaker damage. LOW/MID EQ (12) An active tone control (Peak/notch, ±12 dB) that varies the low/mid frequency range. HIGH/MID EQ (13) An active tone control (Peak/notch, ±12 dB) that varies the high/mid frequency range. HIGH EQ (14) An active tone control (Shelving type, ±15 dB) that varies the high frequency range. MASTER: MAIN REVERB (15) The Main Reverb control determines the desired amount of reverberation from the Internal reverb system. Clockwise rotation increases the reverb effect and counterclockwise decreases the effect. POWER LED (16) Illuminates red when AC power is being supplied to the amp. GROUND SWITCH (17) Three-position, rocker-type switch which, in most applications, should be operated in its center or zero position. There may be some situations when audible hum and/or noise will come from the loudspeaker. If this situation arises, position the ground switch to either positive or negative (+ or -), or until the noise is minimized. Note: Should the noise porblem continue, consult your Authorized Peavey Dealer, the Peavey factory, or a qualified service technician. THE GROUND SWITCH IS NOT FUNCTIONAL ON 220/240 VOLT MODELS. POWER SWITCH (18) Depress the switch to the “on” position. The red LED will illuminate indicating power is being supplied to the unit. 4 Back Panel: KI3/AK 70CJ A PRODUCT OF PEAVEY ELECTRONICS CORP. MERIDIAN MS. MADE IN U.S.A.
Instruments de musique - KB/A 100 (405.05 kb)