|
Instructions Linear, Modèle AE-1
Fabricant : Linear Taille : 236.87 kb Nom Fichier : 9ad095e1-4b2f-418d-b96e-2e95dfe631bc.pdf
Langue d'enseignement:
|
|
|
|
Aller à la télécharger
Facilité d'utilisation
There are no obligations or liabilities on the part of Linear Corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear Corporation Warranty is in lieu of all other warranties express or implied. All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details. IMPORTANT !!! Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed. V For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they have limited transmitter power and therefore limited range. V A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies, regardless of code settings. V Changes or modifications to the device may void FCC compliance. V Infrequently used radio links should be tested regularly to protect against undetected interference or fault. V A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these facts should be communicated to the ultimate users. Copyright © 1999 Linear Corporation 213071 B REFER TO THE AM/II INSTALLATION & PROGRAMMING INSTRUCTIONS FOR DETAILS ON WIRING POWER, EARTH GROUND, REMOTE DEVICES, ANTENNA, CONTROL INPUTS AND RELAY OUTPUTS TO THE AM/II RELAY OUTPUT TO ACCESS DEVICE POWER INPUT TO TRANSFORMER EARTH GROUND CONNECTION USE LOWER WIRING HOLE IF MODEM IS GOING TO BE INSTALLED TELEPHONE LINE (USE MODULAR JACK OR TERMINALS) CONNECT UNITS WITH THE MODEL A2M MODEM CABLE ATTACH MODEM WITH VELCRO ® STRIPS CONNECT MODEM TRANSFORMER POWER CABLE AND SLIDE MODEM POWER SWITCH TO "1" CONNECT INCOMING TELEPHONE LINE TO THE MODEM'S "LINE" JACK USE THE TELEPHONE CABLE SUPPLIED WITH THE MODEM TO CONNECT BETWEEN THE MODEM'S "PHONE" JACK AND THE AE-1 TELEPHONE LINE JACK NOTE: SEPARATE PHONE LINES ARE RECOMMENDED FOR THE MODEM AND AE-1. ONE PHONE LINE CAN BE USED AS SHOWN ALTHOUGH THE ENTRY SYSTEM IS UNAVAILABLE WHILE MODEM IS ON-LINE. 1 2 3 REMOVE THE TWO NUTS AND THE POSTAL LOCK BARRIER PLATE BARRIER PLATE BEND UP TABS ON THE HOLE PLUG AND REMOVE THE PLUG INSTALL THE POSTAL LOCK USING FOUR 10-32 NUTS VERIFY THAT THE LOCK STRIKE ACTIVATES THE MICRO SWITCH AREA 07 TELEPHONE ENTRY NUMBERS 7.1 7.2 7.3 7.4 7.5 Enter Directory Code Directory Code: 0000 Enter Telephone Number Telephone#: ************ Enter Tenant Name Extended Talk Time Yes No Delete Directory Entry Directory Code: 0000 RELAY SETUP AREA 21 21.1 21.2 21.3 21.4 21.5 21.6 Which Relay to Program. CH-A CH-B CH-C CH-D Select Operation: Control Shunt Alarm Obstacle CCTV Select Timing Mode: Time Pulse Toggle Latch Enter Activation Time: Time in seconds: 00000 21.7 21.8 Assign Time Zone [1]: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 21.9 21.10 21.11 Enter Channel Name Assign Telephone Digit None 1 2 3 4 5 6 7 8 9 Channel Control Normal Activate LockOpen LockClosed Assign Time Zone [2]: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Assign Time Zone [3]: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Assign Time Zone [4]: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 TELEPHONE ENTRY SETUP AREA 27 27.1 27.2 27.3 27.4 27.6 Directory Code Length 1 2 3 4 Directory Begins At Beginning(A) Middle(M) PBX Dialing Digit Off 9 8 7 6 5 4 3 2 1 0 27.7 27.8 27.9 27.10 Sort Directory Names Yes No Edit Display Messages Message Number: 00 Set Talk Time Talk Time Seconds: 060 Edit Display Message Max Directory Entries Maximum Entries: 00000 Delete All Tlph. Entries Yes No 27.5 27.11 Assign Postal Key Door CH-A CH-B CH-C CH-D Adjust Hybrid Level Press OK To Start/Stop INSTALLERS OF AE-1 SYSTEMS SHOULD FAMILIARIZE THEMSELVES WITH THE AM/II SYSTEM BY READING THE ENTIRE AM/II INSTALLATION & PROGRAMMING INSTRUCTIONS. PROGRAM AREAS SPECIFIC TO THE AE-1 ARE AREAS 07 & 27. AREA 21 HAS TWO OPTIONS FOR THE AE-1. PROGRAMMING WITH A PERSONAL COMPUTER IS RECOMMENDED, ESPECIALLY FOR ENTERING THE TENANT NAMES. 27.12 Display Briteness Dim Low Med High 27.13 Priority Access ABCD 0 = No 1 = Yes 0000 5 3 4 2 1 REMOVE TEST JUMPER 6 PRESS # TO VIEW DIRECTORY AND ENTER CODE TO DIAL A TEST PHONE NUMBER ADJUST THE SPEAKER VOLUME AND DISPLAY CONTRAST TO SUIT THE ENVRONMENT THE UNIT IS MOUNTED IN HAVE TESTING PARTY PRESS ASSIGNED TELEPHONE DIGIT (DEFAULT IS 9) TO GRANT ACCESS VERIFY THAT THE PROPER RELAY ACTIVATES AND THAT THE ACCESS DOOR STRIKE OR GATE CONTROL ACTIVATES REPLACE THE TEST JUMPER, LOCK THE ...
Écrivez votre propre critique du dispositif
|
|