Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
The STAGEPAS 600i is an all-in-one PA system, consisting of two speakers and a powered mixer. In order to get the most out of your new STAGEPAS 600i and its sophisticated functions, we suggest you read through this manual thoroughly. Also keep it in a safe place for future reference. Main Features • 600 watts power amplifier for versatility in a wide variety of performance applications. • 10-inch two-way bass-reflex type speakers for high-quality, powerful sound. • 10-channel mixer features four mono mic/line and three stereo line input channels to support a wide range of inputs. • Yamaha’s high-quality SPX reverb, providing optimum processing for instruments or vocals. • Feedback Suppressor, which automatically cuts and prevents undesirable feedback noise. • USB connector for convenient digital connection with an iPod/iPhone, and allows charging of the device. • Independent three-band equalizer on each channel for tonal adjustment and sound control. Connecting microphones, instruments, and audio devices to the mixer 4 Connect desired devices, such as a microphone, or an instrument to the input jack of the mixer. Refer to the illustration on the mixer shown below or the connection example of the cover panel of the accessory compartment. Getting sound out of the system 5 Connect the included power cord. First, connect it to the mixer’s AC IN connector, then to a power outlet. 6 Turn the mixer’s LEVEL controls (white knobs) and MASTER LEVEL control (red knob) to the minimum (zero). Also, set the equalizer controls (green knobs) to the center “D” or “MUSIC” position. 7 Set the MIC/LINE switch to the MIC (N) position for microphone connection, and to the LINE (O) position for connection of an instrument or audio device. 8 Turn on the power of the connected sound source (if applicable), then the mixer. The POWER LED lights. 9 Set the MASTER LEVEL control to the “D” position. 10 While playing your instrument or singing into the microphone, use the LEVEL control to adjust the volume of the corresponding channel. 11 Use the MASTER LEVEL control to adjust the overall volume. If you hear the sound and the volume seems appropriate, setup is complete. If not, please refer to the check list in the “Troubleshooting” section on the back of this booklet. NOTE To avoid any loud, unexpected noise from the speaker, first turn off the power to the mixer, then the connected sound source (such as an instrument or audio device). Equalizer Mixer Controls and Functions 1 Mic/Line input jacks (channels 1-4) Connect microphones, guitars, electronic musical instruments or audio equipment. Channels 3 and 4 provide combo jacks that support both XLR and phone plugs. 2 MIC/LINE switches (channels 1-4) For low-level signals (including microphones), set the switch to the MIC (N) position. For high-level signals (including electronic instruments and audio equipment), set the switch to the LINE (O) position. 3 Hi-Z switch (channel 4) This switch is used when connecting a device directly to the mixer without a DI (direct box)—for example, instruments with passive pickups, such as an acoustic-electric guitar or electric bass without battery. This function is effective only for the phone jack input. 4 Line (stereo) input jacks (channels 5/6, 7/8, 9/10) Connect line-level devices such as electronic instruments, acoustic-electric guitars, CD players, and portable audio players. These jacks support phone, RCA-pin, and stereo-mini plugs. NOTE For the channel 7/8 input, if both phone and RCA-pin jacks are used at the same time, the phone jack will take priority. For the channel 9/10 input, if both phone and stereo mini jacks are used at the same time, the stereo mini jack will take priority. The signal from the device connected to another jack will be muted. The music signals from iPod/iPhone (9) are always mixed to channels 9/10. XLR phone RCA-pin stereo-mini 5 MONITOR OUT jacks These are for connection to a powered speaker for monitoring purposes, and output a mix of the signals from channels 1 to 9/10. You can adjust the output level using the MONITOR OUT control (!). If only the L (MONO) jack is used, the signals from the L and R channels are mixed and output. 6| SUBWOOFER OUT jack This is for connection to a powered subwoofer, and outputs a mono signal. If this jack is in use, the low frequencies below 120Hz to the SPEAKERS L/R jacks will be cut. The output level is linked to that of the MASTER LEVEL control (C). 7 REVERB FOOT SW jack This is for connection to an unlatchedtype footswitch such as the Yamaha FC5—useful for solo performers, since you can toggle the reverb on and off as needed with your foot. 8 SPEAKERS L/R jacks Use the included speaker cables to connect the speakers. 9 USB connector Connect your iPod/iPhone using a USB cable to play music and charge the iPod/iPhone. Use the LEVEL control of channels 9/10 to adjust the volume, since the music signals are mixed to those channels. This connector supplies 5V power to the connected USB...