Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
6. Keep operation area clear of all persons. 7. Do not overreach or stand on unstable support. Keep good footing and balance at all times. 8. Follow the maintenance instructions specified in the manual. 9. This product shall be connected to a power supply receptacle protected by a ground fault circuit interrupter. Electrical shock hazard. . NEVER direct water spray toward the power washer or any electrical outlet connection. . NEVER operate the power washer during thunderstorms, or in the rain. . Keep all connections dry and off the ground. . This product is provided with a GFCI for your safety. However, ALWAYS disconnect power before disassembling or repairing the unit. . Inspect cord and GFCI prior to use. Any repair or replacement of the power cord must be performed by a qualified (licensed or certified) electrical technician. . Do not carry the unit while it is in use. . This product requires a grounded 120V, 15 Amp circuit. . If the power receptacles available will not fit this equipment’s power cord, then have an appropriate power receptacle installed by a certified electrician. . The electrical components of this equipment are to be serviced only by qualified technicians. . Do not modify any of the electrical components of this equipment. . No power cord adapter should be used with this equipment. . Check with a qualified electrician or service person if the grounding instructions are not completely understood or you are in doubt as to whether the equipment is properly grounded. 2 PW167600AV Injection hazard. . Keep clear of nozzle. NEVER direct high pressure spray at any person, animal or self. . Always wear safety glasses or goggles and protective clothing. Explosion hazard. . NEVER spray flammable liquids or use pressure washer in areas containing combustible dust, liquids or vapors. Equipment damage. l ALWAYS turn water supply “ON” before turning pressure washer “ON”. Running pump dry causes serious damage. l NEVER allow the unit to run with the trigger released (off) for more than one minute. Resulting heat buildup will damage pump. l NEVER store the pressure washer outdoors or where it could freeze. The pump will be seriously damaged. l Release the trigger when changing from high to low pressure modes. Failure to do so could result in damage to the nozzle. l If an extension cord is needed, the appropriate wire sizes must be used (See chart). l This unit must always be used in the horizontal position. EXTENSION CORDS If using an exten- sion cord, use only Extension Allowable length Cord size 25’ 50’ 14 AWG Yes No 12 AWG Yes Yes grounded, three wire extension cords that are in good condition. Use only extension cords that are intended for outdoor use. These extension cords are identified by a marking “Acceptable for use with outdoor appliances; store indoors while not in use”. Use only extension cords having an electrical rating not less than the rating of the product. Do not use damaged extension cords. Examine extension cord before using and replace if damaged. Do not abuse exten sion cord and do not pull on the cord to disconnect. Keep cord away from heat and sharp edges. Always disconnect the cord from the receptacle before disconnecting the product from the extension cord. Note: Do not use 16 or 18 AWG extension cords on this product. Figure 5 5. Attach opposite ring in the same manner (Figure 6). Installation Instructions Tools Required for Installation: . Flat Screwdriver l Hammer/Mallet l Adjustable Wrench 1. Set plastic spacer (included in parts pack) on workbench (Figure 1). Figure 2 3. Tap the retaining ring onto the axle (Figure 3 & 4). Figure 6 6.Slide wheels out and snap axle into place on the underside of body (Figure 7). 7.Snap wheel covers on the wheel. 8.Attach foot to front of pressure wash- er body (Figure 7). Figure 7 9.Hook up chemical suction hose to the tip on the bottom of the handle (Figure 8). Figure 1 2.Place “star shaped” retaining ring on the spacer (tangs pointing down) (Figure 2). Figure 3 Figure 4 Figure 8 10. Attach black handle with enclosed screws and washers (Figure 9). Figure 9 4. Put both wheels on axle, solid sides together (Figure 5). 3 Electric High Pressure Washer Setup and Operating Instructions THINGS TO REMEMBER 1. Always check the inlet filter for debris. 2. Always reset the Ground Circuit Interrupter (GFCI) each time the unit is plugged into an outlet. 3. Never direct a single point spray at a soft or breakable surface. GARDEN HOSE CONNECTION INSTRUCTIONS 1. Attach nipple adapter to inlet fitting on the unit. 2. Attach quick connect to garden hose. 3. Pull side “A” of quick connect toward garden hose and push onto nipple adapter. 4. Push side “A” of quick connect towards nipple adapter and release. "A" Figure 10 SYSTEM CONNECTION 1. Ensure that the power switch is in the OFF position. 2. Attach high pressure hose and gun assembly to the unit. 3. Insert lance into the gun and turn clockwise to positive stop as shown in Figure 11. Figure 11 4.Connect ...