Évaluations - 3, GPA: 5
(
)
)
|
Facilité d'utilisation
EXTERNAL TRIGGERS SPEAKERS EXTERNAL MIDI DEVICE 1 Quick Setup Guide 1. Make sure all items listed on the front of this guide are included in the box. 2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE PRODUCT. 3. Study this setup diagram. 4. Place the drum station in an appropriate position for operation – either on a flat surface, such as a table or attach to a drum clamp set mount (sold separately). 5. Make sure all speaker devices are turned off and all volume knobs/faders are at “zero.” 6. Connect all input sources as indicated in the diagram. 7. Connect the outputs to headphones, and/or powered amplifier stereo system. 8. Plug in both power adapters and other devices into AC power. 9. Switch everything on in the following order. a. iED04 Digital Drum Station. b. Any external devices. c. Any external speakers. 10. When turning off, always reverse this operation by, a. Any external speakers. b. Any external devices. c. iED04 Digital Drum Station. NOTE: Speakers, external sound device, additional triggers and CD player are NOT included. As shown in the above figure, the supplied RCA cable is used to connect to an external amplifier, mixer, or a home stereo systems. Getting Started This section will cover how to begin using your Digital Drum Station. Be sure that your setup matches the diagram as previously shown. • Be sure that the iED04 is powered on. While the unit is powered on, turn the volume up on the back panel half way. 1. Strike the drum pads with the included sticks. This should produce a sound. 2. 2 3. To change the drum kit: a. Press “DRUM SET.” The display will show the current drumset number. b. To change the sounds, press the up and down arrows. 4. To play along to preset patterns: Make sure that the Digital Drum Station is in ‘Pattern’ Mode. If ‘Pattern’ a. is not displayed on the screen, press the “PATTERN/SONG” button until it appears. Make sure that you are in ‘Preset’ Mode. Press the button labeled b. “PRESET/USER.” The display should show the current preset (i.e. ‘Rock 1’). Use the up and down arrows to change and shuffle through the 50 c. different patterns. d. Press “PLAY” to hear the preset pattern. e. Tempo can be adjusted by the tempo up and down buttons. You can play along with the preset samples on the drum pads. To add a f fill press the “FILL” button while the sample is playing. 5. To record a drum pattern: a. Press the button labeled “PRESET/USER” until the display shows ‘USER’. Press the “PERFORM/COMPOSE” button until the display shows b. “COMPOSE” and “RECORDING”. Press “PLAY” to start recording. You will hear a click sound corresponding to the tempo of the current pattern. The recording will c. continually loop through the pattern so that you may add drum parts one at a time. d. You can enter drum beats by striking the pads. e. Press “STOP” to stop the recording. f. Press “PLAY” to hear the recorded pattern. TIP: You can use the “STOP” button to TIP: Each pattern can hold two related sequences and manually adjust the tempo. Simply tap fills. You can switch between the sequences while the “STOP” button repeatedly – the playing a preset by pressing “A” and “B” buttons. You tempo will be set to how fast you tap can also alternate between the two fills by holding down the button. “A” or “B” and then pressing “FILL”. NOTE: To reset the unit, erasing all stored values to return to the default modes, hold down “ERASE” and “PLAY while powering the unit on. 3 Pad Arrangement Below is a diagram describing how the pads correspond to most of the sounds from each kit. This diagram also shows which MIDI note number the iED04 will transmit when controlling an external device via MIDI. CRASH RIDE HIGH TOM LOW TOM CYMBAL CYMBAL MIDI NOTE MIDI NOTE MIDI NOTE MIDI NOTE #48 #45 #49 #51 BASS KICK SNARE CLOSED HI OPEN HIDRUM DRUM HAT HAT MIDI NOTE MIDI NOTE MIDI NOTE MIDI NOTE #36 #38 #42 #46 If you are using an external footswitch (sold separately) connected to the KICK input on the back of the iED04, pressing it down will generate a bass kick drum and MIDI note #36. If you are using an external footswitch (sold separately) connected to the HI-HAT input on the back of the iED04, pressing it down will simulate the behavior of a closed hihat and generate a closed hi-hat sound (MIDI note #42) evry time it is pressed down. While the footswitch is pressed down, hitting the OPEN HIHAT pad will generate a closed hihat sound (MIDI note #42). When you release the footswitch, hitting the OPEN HI-HAT pad will generate an open hihat sound. NOTE: For best results, strike the middle of the pad. Striking the edge of the pad could result in the triggering of an adjacent pad. 4 Bateria digital iED04 MANUAL DE INICIO RAPIDO DEL USUARIO Contenido de la caja BATERIA DIGITAL iED04 BAQUETAS CABLE DE .” A RCA ADAPTADOR DE 9 vca AURICULARES Diagrama de conexion REPRODUCTOR DE CD O MP3 AURICULARES NOTA: ADAPTADOR DE ALIMENTACION LOS DISPOSITIVOS EN LINEA PUNTEADA NO ESTAN INCLUIDOS . DISPAROS EXTERNOS ALTAVOCES DISP...