Increasing gain adds distortion, or an overdriven rock tone; decreasing gain produces a cleaner sound. 5. TONE Turn right to add treble/reduce bass. Turn left to add bass/reduce treble. 6. POWER Turns amplifier on/off. 7. POWER ADAPTOR INPUT A power adaptor is NOT included. As an alternative to two 9V batteries, it is possible to power this amp with an adaptor. IMPORTANT - use only a 14V, 500mA adaptor with this amplifier (sold separately). INSTALLING BATTERIES The MA003 Amplifier opera

ALL RIGHTS RESERVED 7 PIECE DRUM SET DRUMS [A] 12” Snare Drum [B] 10” Tom Drum [C] 13” Floor Tom Drum [D] 18” Bass Drum CYMBALS [E] 12” Hi-hat Cymbals (2) [F] 14” Crash Cymbal STANDS / HARDWARE / DRUM HEADS [G] Snare Stand [H] Hi-hat Stand [I] Cymbal Stand [J] Bass Drum Pedal w/ Felt Beater [K] Tom Tom Mounting Arm w/ Memory Clamp [L] Bass Drum Spurs (2) [L.1] Retractable Rubber w/ Spiked Tip [M] Floor Tom Legs (3) [N] Bass Drum Tension Rods w/ Washers (12) [O] Bass Drum Rim Claws (12) [P] Bass

Increasing gain adds distortion, or an overdriven rock tone; decreasing gain produces a cleaner sound. 5. TONE Turn right to add treble/reduce bass. Turn left to add bass/reduce treble. 6. POWER Turns amplifier on/off. 7. POWER ADAPTOR INPUT Connect the power adaptor included with your amp here. Use only the adaptor supplied with this amplifier. SPECIFICATIONS Output Power: 4 watts RMS Frequency Range: 60 Hz ~ 6 kHz Speaker: 4" / 8W / 4 ohms Input Sensitivity: 26 mV Power Supply: 14

Attach the bass drum pedal (F) by sliding the bottom plate under the flanged rim of the bass drum. Tighten the top clamp located under the footboard just enough to “grab” the top of the flanged rim. Place the bass drum felt beater into the top of the bracket and adjust so the felt beater hits the middle of the drum. Make sure the spring on the side of the pedal is tensioned to the top and bottom of the bracket of the bass drum pedal. Stand behind the bass drum and insert the two L mounting arms

. Enjoy! 3 Open the box and remove the seat top (*not included with model FD-514) Then take out the snare drum (A) tom drum (B) and cymbal (D) and put aside. The pedal, stands and accessories are located in the side compartment. Open up the package and inspect the items with the contents page. Take out the bass drum (C) and place upright on the floor. Insert the two bass drum spurs (H) to the front half of the bass drum on the bottom. The spurs should extend out from the drum just enough to stea

Intended for use as a seat only. Do not stand. * 4 piece drum set does not include seat 5 piece drumset *FD-514 / FD -515 / FD -517 / FD -520 * 4 piece drum set does not include seat DRUMS (A) Snare Drum (B) Tom Drum (C) Bass Drum CYMBALS (D) Cymbal STANDS / HARDWARE (E) Cymbal Arm (F) Bass Drum Pedal w/ Felt Beater (G) L Mounting Arms (2) (H) Bass Drum Spurs (2) (I) Drum Tuning Key (J) Seat *(not included with FD-514) (K) Cowbell *(FD-520 only) (L) Drumsticks (2) CONTENTS 2 Open the box and rem

Replace the top felt and wing nut. Place the cymbal arm into the mount furthest away to you at the front of the bass drum. You can now adjust the height and tighten. Place the drum seat (J) behind the drum set. (*Not included with model FD-514) Now grab the pair of drumsticks (L) and play. Have fun! Use the drum-tuning key (I) to make any small changes in tuning. Turning the tension rods to the right will raise the pitch of the drum. Turning the tension rods to the left will loosen or lower the

12346785 Important Safety Instructions Please read this section carefully. 1. Read and follow these instructions. 2. Do not use this device near water. 3. Clean only with a dry cloth. 4. Do not use near any heat sources such as radiators, heaters, or stoves. 5. Only use the attachments/accessories specified by the manufacturer. 6. Refer all servicing to qualified service personnel. Servicing is required when the drum pad has been damaged in any way, liquid has been spilled onto the drum pad, the

Increasing gain adds distortion, or an overdriven rock tone; decreasing gain produces a cleaner sound. 5. TONE Turn right to add treble/reduce bass. Turn left to add bass/reduce treble. 6. POWER Turns amplifier on/off. 7. POWER ADAPTOR INPUT Connect the power adaptor included with your amp here. Use only the adaptor supplied with this amplifier. SPECIFICATIONS Output Power: 4 watts RMS Frequency Range: 60 Hz ~ 6 kHz Speaker: 4.5" / 8W / 4 ohms Input Sensitivity: 26 mV Power Supply:

Increasing gain adds distortion, or an overdriven rock tone; decreasing gain produces a cleaner sound. 5. TONE Turn right to add treble/reduce bass. Turn left to add bass/reduce treble. 6. POWER Turns amplifier on/off. 7. POWER ADAPTOR INPUT Connect the power adaptor included with your amp here. Use only the adaptor supplied with this amplifier. SPECIFICATIONS Output Power: Power Supply: 4 watts RMS 14V DC 500mA Frequency Range: Dimensions: (LxWxH) 60 Hz ~ 6 kHz 8" x 3.25" x 7.5" S