Log:
Évaluations - 1, GPA: 4 ( )

Instructions Task Force, a Lowe's brand, Modèle 83691

Fabricant : Task Force, a Lowe's brand
Taille : 807.06 kb
Nom Fichier : 94c57821-b63f-44ba-a9e9-4881a022f6cf.pdf
Langue d'enseignement: en
Aller à la télécharger



Facilité d'utilisation


Midwest Air Technologies, Inc., 625 Barclay Boulevard, Lincolnshire, IL 60069 Task Force® is a registered trademark of LF, LLC. All Rights Reserved Part No. E100186 Rev.01 TABLE OF CONTENTS Page Safety Definitions .................................................................................................. 3 Glossary ................................................................................................................ 3 Duty Cycle ............................................................................................................ 3 Description of Operation ....................................................................................... 3 Important Safety Instructions & Guidelines .......................................................... 4 Set-up for Operation ............................................................................................ 5 Operating Procedures ........................................................................................... 6 Maintenance ......................................................................................................... 6 Routine Maintenance Schedule ............................................................................ 6 Storage .................................................................................................................. 6 Troubleshooting Guide .......................................................................................... 7 Exploded Parts Diagram ...................................................................................... 8 Parts List .............................................................................................................. 9 Limited Warranty .................................................................................................. 10 Safety Definitions The information listed below should be read and storing the air compressor. We utilize the symbols understood by the operator. This information is below to allow the reader to recognize important given to protect the user while operating and information about their safety. Indicates an imminently hazardous situation which, if Indicates a potentially hazardous situation which, if not not avoided, will result in death or serious injury. avoided, may result in minor or moderate injury. Indicates a potentially hazardous situation which, if not When used without the safety alert symbol indicates a avoided, could result in death or serious injury potentially hazardous situation which, if not avoided, may result in property damage. Glossary CFM: Cubic feet per minute. Cut-In Pressure: The air compressor will automatically start to refill the tank when the pressure drops SCFM: Standard cubic feet per minute; a unit of measure below the prescribed minimum. for air delivery. Cut-Out Pressure: The point at which the motor stops PSlG: Pounds per square inch gauge; a unit of measure when the tank has reached maximum air pressure. for pressure. Code Certification: Products that bear one or more of ASME: American Society of Mechanical Engineers. the following marks: UL, ETL or CSA have California Code: Unit may comply with California Code been evaluated by OSHA certified independent 462 (I) (2)/(M) (2). safety laboratories and meet the applicable Underwriters Laboratories Standards for Safety. Duty Cycle This air compressor pump should not run more than 20 minutes per hour. If the pump runs more than 30% of the duty cycle, the air requirement is greater than that which is supplied by the unit. You may need to check Description Drain Valve: Used to drain condensation from the air tank. Located at bottom of tank. Fan Cooled: This unit is equipped with a cooling fan which may continue to run after the pump has stopped. On/Off Switch: This controls the power to the motor and also the switch serves as the on/off positions for the air compressor. Air Intake Vents: Provide clean air to the pump and must always be kept free of debris. Check on a daily basis or before each use. Air Compressor Pump: Pressurizes air from the atmosphere and stores it in a reserve tank. for restrictions in the air line, use a larger diameter hose, or purchase an air compressor that better matches your air requirements. of Operation Tank Safety Valve: Used to allow excess tank pressure to escape into the atmosphere. This valve should only open when the tank pressure is above the maximum rated pressure of the model. Regulator Pressure Gauge: Indicates the outgoing air pressure to the tool and is controlled by the regulator. Tank Pressure Gauge: Indicates the reserve air pressure in the tank. Regulator: Controls the pressure leaving the air tank. Tools require different operating pressures. Refer to the tool manufacturers manual before connecting to the compres sor. To increase the pressure turn the knob clockwise and to decrease the pressure turn the knob counterclockwise. Important Safety Instructions and Guidelines • Save all instruct...


Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories