Évaluations - 2, GPA: 4.5
(
)
)
|
Facilité d'utilisation
2. Total connected load: 1680 watts. 3. Plan to run 120vAC, 60 Hz wiring (with ground) on a separate 20 Amp circuit from a power source, through the provided wall switch, to the housing’s junction box. See wiring diagram. INSTALLATION IN NEW CONSTRUCTION PREPARATION 1. Loosen hanger bar brackets to allow bars to be inserted. 2. Refer to Figure 2. Insert hanger bars into brackets. 3. Refer to Figure 3. Slide hanger bar brackets down to end of slot closest to outside edge of housing. Tighten brackets in this position. 4. Refer to Figure 4. Remove junction box cover by removing one screw. 5. Refer to Figure 4. Remove appropriate wiring knockout(s) and install approved box connector(s). FIGURE 1 FIGURE 2 FIGURE 3 FIGURE 4 73.4" 14" HANGER BARS ADJUSTMENT SLOT JUNCTION BOX COVER KNOCKOUTS 93.4" MOUNTING THE HOUSING 1. Locate housing between joists. 2. Refer to Figure 5. Using nails, secure hanger bars to joist. NOTE: The hanger bar brackets are adjustable. Allowing for the thickness of the finished ceiling, mount hanger bars so that edge of housing will be flush with the finished ceiling. 3. Adjust brackets as required. Tighten brackets. INSTALLING THE SWITCH 1. Install double-gang switch box in chosen location. 2. Refer to Figure 6. Run wiring and make wiring connections. 3. Use supplied screws to secure switch bracket assembly to switch box. 4. Using supplied screws, secure wall plate to switch bracket. INSTALLING AND CONNECTING THE WIRING Refer to Figure 6. All wiring must comply with local codes and unit must be properly grounded. 1. Using 12-gauge wire, run 120vAC, 60 Hz wiring (with ground) from a power source to the wall switch location. The unit must be wired on a separate 20 Amp circuit. 2. Run wiring from switch location to housing as shown in the wiring diagram. 3. Make wiring connections as shown in wiring diagram. 4. Replace junction box cover. Slide slotted hole in cover over screw. Tighten screw securely. 5. Secure wire cover with one screw. 6. Insert heater and ventilator plugs into proper receptacles as shown. MOUNTING THE GRILLE ASSEMBLY 1. Refer to Figure 7. Place the reflector into the grille. 2. Refer to Figure 8. Insert light plug and night light plug into receptacles. 3. Refer to Figure 7. Using two provided screws, secure grille and reflector to housing. 4. Install 100 watt (maximum) light bulb into light socket. 5. Install 7 watt (maximum) C-7 candelabra type bulb into night light socket. 6. Refer to Figure 9. Snap lens into place. FIGURE 7 FIGURE 6 (LENS OMITTED FROM DRAWING FOR ILLUSTRATIVE PURPOSES) HEATER JUNCTION BOX HEATER (WHITE) LIGHT RED WHT BLKWHT BLKWHT NIGHT LIGHT SWITCH BOX LIGHT HEAT NIGHT LIGHT 120vAC LINE GROUNDWHITEBLACKNOTE: WHEN THERMOSTAT OR TIMER IS USED, CONNECT AT T T GRILLE FIGURE 5 INSTALLATION IN EXISTING CONSTRUCTION In an existing, finished building, installation of the Heat- Light Combination requires an accessible area (attic or crawl space) above the planned location. If the location that has been chosen for installation has a finished floor above it, be certain there is sufficient space available to install the housing. PLANNING Review “INSTALLATION IN NEW CONSTRUCTION” and follow all instructions that apply. CAUTION: Check the area above the planned location to make sure that: (1) Wiring can be run to the planned location. (2) No wiring or other obstructions might interfere with the installation. INSTALLATION 1. The housing must be mounted between ceiling joists. 2. Refer to Figure 10. Mark ceiling for cutout. Cutout dimensions: 141.8" long x 97.8" wide. Make cutout in ceiling. 3. Follow steps under “PREPARATION” page 1. 4. From above, lower housing into the cutout and secure hanger brackets. Run wiring through box connectors. 5. From below, adjust housing so that it is flush with the finished ceiling. 6. Form below, make wiring connections as shown in figure 6. 7. Replace junction box cover. 8. Insert heater, light, and night light plugs into proper receptacles. 9. Install grille, reflector and lens. FIGURE 8 NIGHT LIGHT LIGHT HEATER FIGURE 10 FIGURE 9 LENS(LENS DETACHED IN DRAWING FOR ILLUSTRATIVE PURPOSES) 141.8" 97.8" One Year Limited Warranty WARRANTY OWNER: NuTone warrants to the original consumer purchaser of its products that such products will be free from defects in materials or workmanship for a period of one (1) year from the date of original purchase. THERE ARE NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. During this one year period, NuTone will, at its option, repair or replace, without charge, any product or part which is found to be defective under normal use and service. THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS OR TUBES, FILTERS, DUCT, ROOF CAPS, WALL CAPS AND OTHER ACCESSORIES FOR DUCTING. This warranty does not cover (a) normal maintenance and service or (b) any products or parts which have been subject to misuse, negl...