Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Do not alter or adjust any part of 3. the equipment or its engine that is sealed by the manufacturer or distributor. Only a qualified service technician may adjust parts that may increase or decrease governed engine speed. Wear ANSI-approved safety goggles, 4. heavy-duty work gloves, and dust mask/respirator during service. Maintain labels and nameplates on 5. the equipment. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Have the equipment serviced by a 6. qualified repair person using only identical replacement parts. This will ensure that the safety of the equipment is maintained. Do not attempt any service or maintenance procedures not explained in this manual or any procedures that you are uncertain about your ability to perform safely or correctly. Store equipment out of the reach of 7. children. Follow scheduled engine and equip8. ment maintenance. Tanks rust from moisture build-up, 9. weakening the tank. Drain tank daily and inspect periodically. Do not remove or adjust safety valve.10. Refueling:11. Do not smoke, or allow sparks, a. flames, or other sources of ignition around the equipment, especially when refuelling. Do not refill the fuel tank while the b. engine is running or hot. Do not fill fuel tank to the top. Leave c. a little room for the fuel to expand as needed. Refuel in a well-ventilated area only.d. Save these instructions. This page intentionally left blank Basic Specifications Equipment Lubricant Type Compressor Oil Capacity 1.37 Quarts Engine 65204 13 HP, EPA/CARB Compliant 99918 13 HP, EPA Compliant Rotation viewed from PTO (power takeoff - the output shaft) Counterclockwise Engine Shaft O 1” x 2-7/8” Long 1/4” Keyway 3/8”-24 UNF inner thread Air Pressure Range 145-175 PSI Air Outlet 3/4" NPT Air Flow 19.5 CFM @ 40 PSI 18.7 CFM @ 100 PSI Engine Idle Speed 1,800±100 RPM (Pressure switch controlled) Note: Engine specifications are found in the engine manual supplied with this equipment. Components and Controls Ball ValveTank DrainAir Storage TankOil Sight GlassBelt GuardPilot ValveSafety ValveTank Pressure GaugeAir FilterFig. 1 1. Belt Guard. The Belt Guard (A1) encloses the pulleys and drive belts. It protects the user from the moving parts and allows the large pulley to direct cooling air to the Air Pump (A2). Oil Sight Glass. The oil sight glass 2. shows proper level of the oil. Oil level should be at center of Sight Glass. Tank Drain Valve. The Air Tank (A18) 3. drain valve allows moisture to be removed from the tank to reduce the chance of corrosion inside the tank. Safety Valve. This Safety Valve (A15) 4. automatically releases air if the Air Tank (A18) pressure exceeds the preset maximum. In an emergency, the ring could be a. pulled to reduce tank air pressure. Ball Valve. Air hose attaches to this 5. valve. Air pressure required by tools is set by an air pressure regulator. Regulator and Gauge (Not Included). Outlet air can be regulated by adjusting the regulator knob. Clockwise will raise outlet pressure and counterclockwise will lower outlet pressure. Outlet pressure will be displayed on the regulator’s pressure gauge. Air Storage Tank. The Air Tank (A18) 6. is where air pressurized by the Air Pump (A2) is stored for later use. Tank Pressure Gauge. The Air Tank 7. Pressure Gauge (A20) displays the air pressure in the tank. Pilot Valve 8. Pilot Valve. Open the Pilot Valve before starting the engine. It relieves resistance on the engine to make starting easier. It is shown in the open position above. Push the pin over to one side to close it. Equipment Set Up Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagrams near the end of this manual. Unpacking Note: Do not use the air cleaner to lift or move the compressor. It is not designed to withstand such force. When unpacking, make sure that the item is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at 1-800-444-3353 as soon as possible. Mounting The compressor may vibrate strongly 1. during use, so mounting is needed to prevent movement. Before use, mount the compressor 2. securely using all four mounting holes to a solid, level surface, such as a concrete slab or truck bed. Rubber pads (not included) may be 3. used at the mounting points to reduce vibration. Equipment Oil Fill IMPORTANT. To prevent property damage and voiding of the warranty: Before first use, fill the compressor with compressor oil as follows: Remove the Breather Vent (22) and 1. fill with 1.37 quarts of premium quality SAE 30-weight, non-detergent, synthetic air compressor oil. Do not mix oils of different types. Check the oil level at the Oil Sight 2. Glass. The oil level should be at the middle of the Glass. Add or drain oil as ...
Ce manuel est également adapté pour les modèles :matériel de pompage - 65204 (983.84 kb)