Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
The compressor has a grounding plug that looks like the plug illustrated above in 125 V~ 3-Prong Plug and Outlet. 8. The outlet must be properly installed and grounded in accordance with all codes and ordinances. 9. Do not use an adapter to connect this compressor to a different outlet. Symbology PSI Pounds per square inch of pressure CFM Cubic Feet per Minute flow SCFM Cubic Feet per Minute flow at standard conditions NPT National pipe thread, tapered NPS National pipe thread, straight Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V~ Volts Alternating Current A Amperes Specifications Electrical Rating 120V~ / 60Hz / 2A Motor 1,750 RPM Power Cord 6. Long Power Cord (18AWG x 3C) Thermal Protection Automatic shut-off on overload/overheat and automatic reset Maximum Air Pressure / Automatic Shut Off 58 PSI Automatic Restart 43 PSI Air Output .5 CFM @ 20 PSI Air Outlet Size 1/8.-28 NPS Air Outlet with 1/4.-18 NPT Male Adapter Hose Dimensions .236. OD x .157. ID x 10. Long (1/8.-28 NPS Female Adapter - both sides) Base Dimensions 7-3/8. L x 5-3/8. W x 1. H Setup - Before use: Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch “OFF” and unplug the Air Compressor from its electrical outlet before assembling or making any adjustments to the compressor. Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Before operating, make sure the Air Compressor is set up in a well-ventilated area, on a flat, level, solid surface well away from any flammable objects, such as drapes. Never paint in an area without proper ventilation, or near possible ignition sources. Figure A: FunctionsPower Switch(34) Air Hose (43) Water DrainValve (41) Handle(30) Pressure Gauge (11) Pressure Regulator (40) Operating Instructions Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Compressor Area Set Up 1. Designate a work area that is clean and well.lit. The work area must not allow access by children or pets to prevent injury. 2. Locate the Compressor on a flat level surface to ensure proper pump lubrication and to prevent damage to the unit. Keep at least 12. of space around the unit to allow air circulation. 3. Route the power cord from the compressor to the grounded wall outlet, along a safe path without creating a tripping hazard or exposing the power cord to possible damage. General Operation 1. Insert the Power Cord Plug (35) into the nearest 120 volt, grounded, electrical outlet. 2. Connect an Air Brush (not included) to the Air Hose (43) of the Compressor. Use Hose Adapter (44) if needed. Note: Use this Compressor only with air brushes; do not use this compressor with any other type of painting equipment. 3. Turn the Power Switch (34) on. Note: The Compressor will automatically begin to run when the air pressure falls below 43 PSI. When the maximum air pressure (58 PSI) is reached, the Compressor will automatically switch to idle and the Compressor will stop operating. The Compressor will automatically restart when the air pressure falls below 43 PSI. 4. Adjust the regulated air pressure output as shown on the Pressure Gauge (11) by lifting the Regulator Knob (40), turning it to the desired pressure and pressing it back down. 5. When finished using the Air Compressor, turn its Power Switch (34) off. Release any remaining air in a safe fashion and disconnect the Air Brush. Briefly depress the Water Drain Valve (41) to empty the unit of water after each use. 6. Store the Air Compressor in a clean, dry, safe location out of reach of children and other unauthorized people. Maintenance and Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn the Power Switch “OFF” and unplug the Compressor from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY FROM COMPRESSOR FAILURE: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. Cleaning, Maintenance, and Lubrication 1. BEFORE EACH USE, inspect the general condition of the Air Compressor. Check for loose hardware, misalignment or binding of moving parts, damaged belts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. 2. AFTER USE, push the Water Drain Valve (41) under the Filter Cup to drain out the moisture. Also, wipe external surfaces of the compressor with a clean cloth. 3. Store the Air Compressor in a clean, dry, safe location out of reach of children and othe...