Évaluations - 2, GPA: 5
(
)
)
|
Facilité d'utilisation
Once you've found this best position, always keep the remote control unit there. • This appliance has a built-in 3-minute time delay circuit to ensure reliable operation. If the operation button is pressed, the compressor will start running after three minutes. In the event of power failure, the unit will stop. When the power is applied, the unit will re-start automatically after 3 minutes. • To prevent the appliance from malfunctioning, do not set any selector switch between two indicated positions. Make sure that it clicks into position. Operation with the Remote Control Unit (continued) If the outdoor temperature is too cool: When the outdoor temperature stays at around 59° F, the air conditioner suspends the cooling operation and the STANDBY (orange) lamp keeps on flashing. When it becomes warmer, the air conditioner automatically resumes the cooling operation. Night Setback Mode in Cooling What does the Night Setback mode mean? 0N I/0FF O Q COOL I HEAT FAN lAUTO MODE NORM. PROGRAM IoffI ON limn TIMER LOW HIGH I MED. I AUTO imui FAN SPEED COOLER WARMER CD CD TIMER HH MM CD CD PROGRAM ★ night setback SWEEP STEP 1 STEP 1: Press the NIGHT SETBACK button in cooling. The ( * ) mark appears at the lower left of the display. Press the NIGHT SETBACK button again to release the night setback function. This button has no effect in the FAN mode. Room Setting temperature In this mode, the air conditioner will cool the room to the set temperature, and then the thermostat will make the unit pause. After about 30 minutes, the air conditioner will automatically raise the set temperature by 2° F. When the room temperature reaches the newly set value, the thermostat will cause the unit to pause. After about 30 minutes the temperature will again be raised by 2° F. This enables you to save energy without sacrificing comfort. This function is convenient when gentle cooling is needed. 2. Adjusting the Fan Speed A. Automatic STEP 1: Simply set the FAN SPEED selector to the "AUTO" position. A microcomputer in the air conditioner automatically controls the fan speed when the AUTO mode is selected. When the air conditioner starts operating, the difference between the room temperature and the set temperature is detected by the microcomputer which then automatically switches the fan speed to the most suitable level. 07-346-10 Operation with the Remote Control Unit (Continued) Cooling mode: Heating mode: B. Manual 3. Fan Only When difference between room temperature and set temperature is FAN SPEED 4°F and over High Between 4°F and 2°F Medium Below 2°F Low When difference between room temperature and set temperature is FAN SPEED 2°F and over High Below 2°F Medium If you want to adjust fan speed manually during cooling, just set the FAN SPEED selector as desired. [HIGH. MED., or LOW] STEP 1 STEP 2 If you want to circulate air without any temperature control, follow these steps: STEP 1: Set the MODE selector switch to FAN. STEP 2: Press the ON/OFF operation button. Operation with the Remote Control Unit (Continued) STEP 1 STEP 2 STEP 5 4. Heating STEP 1 STEP 2 STEP 3 STEP 4 STEP 5: To stop Set the MODE selector switch to HEAT. Set the timer selector switch to NORM. Press the ON/OFF operation button. Press the COOLER or WARMER button to set a cooler or warmer temperature. Each time you press these buttons, the set temperature varies by 2°F. 84°F max. 64°F min. Set the fan speed selector switch to the setting you want, the air conditioner, press the ON/OFF operation button again. NOTE CAUTION Choose the best position in the room for the remote control unit, which also acts as the sensor for room comfort and transmits the operating instructions. Once you've found this best position, always keep the remote control unit there. This appliance has a built-in 3-minute time delay circuit to ensure reliable operation. If the operation button is pressed, the compressor will start running after three minutes. In the event of power failure, the unit will stop. When the power is applied, the unit will re-start automatically after 3 minutes. To prevent the appliance from malfunctioning, do not set any selector switch between two indicated positions. Make sure that it clicks into position. 07-346-12 CAUTION If the outdoor temperature is extremely low, it is recommended to use another heating appliance: When the outdoor temperature falls to around 10° F, the compressor stops. In this case, to prevent room from freezing, use another heating appliance. ON I/OFF-O Q NORM. PROGRAM OFF I ON COOL I HEAT FAN | AUTO MODE I (711 TIMER LOW HIGH I MED. I AUTO FAN SPEED COOLER WARMER CD CD TIMER HH MM CD CD r-►OFF ►ON 1-CLOCK ’*-J d PROGRAM ★ NIGHT SETBACK SWEEP STEP 1 Night Setback Mode STEP 1: Press the NIGHT SETBACK button in cooling. in Heating The ( * ) mark appears at the lower left of the display. Press the NIGH7 SE7BACK button again to release the night set...
Ce manuel est également adapté pour les modèles :matériel de pompage - KHS1822 (1.11 mb)