Évaluations - 4, GPA: 3.8 ( )

Fabricant : Campbell Hausfeld Taille : 1.88 mb Nom Fichier : Langue d'enseignement:

Never connect green (or green and yellow) wire to a live terminal. 3 . Check with a qualified electrician or serviceman if grounding instructions are not completely understood, or if in doubt as to whether product is properly grounded. Do not modify plug provided; if it will not fit outlet, have proper outlet installed by a qualified electrician. Overheating, short circuiting and fire damage will result from inadequate wiring, etc. 2 FP202801, FP202901, FP202897, FP202999DB, FP202999DQ, and FP202899TT ON/OFF Switch Drain Valve Safety Valve Pressure Gauge Handle Figure 2 - Unit Identification Air Outlet O p e r a t i o n DEFINITION OF TERMS ON / OFF Switch ( I / O ) -Push switch to the ON ( I ) position to turn compressor on. Push switch to the OFF ( O ) position to turn compressor off. This switch should be in the OFF ( O ) position when connecting / disconnecting power cord from electrical outlet or when changing tools. OFF Position Figure 3 ON Position Pressure Switch (located internally)When the compressor is turned ON, this switch will shut compressor off automatically when tank pressure reaches maximum shut-off / cut-out pressure. If compressor remains on and air is depleted from tank, this switch will allow compressor to automatically restart at the restart / cut-in pressure. Pressure Gauge - This gauge reads air pressure in pounds per square inch (psi) in the compressor tank. Make sure this gauge reads ZERO BEFORE changing air tools or disconnecting hose from outlet. ASME Safety Valve - This valve automatically releases air if the tank pressure exceeds the preset maximum. Handle - Designed to move the compressor. Drain Valve - This valve is located on the bottom of the tank. Use this valve to drain moisture from the tank daily to reduce the risk of corrosion. Figure 4 L U B R I C A T I O N This is an oilless product and D O E S N O T require lubrication to operate. BEFORE FIRST STARTUP BREAK-IN PROCEDURE (Complete this procedure before using compressor for the first time. Once completed, it is not necessary to r e p e a t . ) 1. Do not attach a hose or any other fitting to the compressor air outlet. 2. Turn on/off switch to OFF position. 3. Plug in power cord. 4. Turn on/off switch to ON position. Allow compressor to run for 5 minutes. 5. Turn on/off switch to OFF position. 6. Unplug power cord. BEFORE EACH STARTUP OPERATING PROCEDURE 1. Connect air hose to open port located below pressure gauge. 2. Attach the necessary fitting or tool to open end of air hose. 3. Turn on/off switch to OFF ( O ) position. 4. Plug in power cord. 5a. If using inflation needles/nozzles: Attach air hose with inflation fitting to the object you are going to inflate. While holding inflation fitting firmly in place, turn on/off switch to ON position. Allow compressor to inflate the object. Turn off compressor and remove inflation fitting. 5b. If using tire chuck or tool: Once chuck or tool is attached to air hose, turn on/off switch to ON position and allow compressor to run until it automatically shuts off. When using tire chuck to inflate tires, observe gauge reading on compressor and periodically check tire pressure with a separate tire gauge to prevent overinflation. 6 . Operate tool per instructions. As air is depleted from the tank by use of a tire chuck, tool, etc., the compressor will restart automatically at its preset “cut-in” pressure. When a tool is being used continuously, the compressor will cycle on and off automatically. 7 . Turn switch to OFF ( O ) position, unplug power cord and drain tank of air when finished using compressor. M a i n t e n a n c e Disconnect power source then release all pressure from the system before attempting to install, service, relocate or perform any maintenance. Service should be performed by an authorized service representative. 3 Oilless Compre s s o r s M a i n t e n a n c e ( C o n t i n u e d ) The compressor should be checked often for any visible problems and the following maintenance procedures should be performed each time the compressor is used. ASME SAFETY VALVE Do not remove or attempt to adjust the safety valve! Figure 5 Check the safety valve by performing the following steps: ...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :