Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Quick Connect Offers a quick attaching and release feature for removing the air hose. Regulator The air pressure coming from the air tank is controlled by the regulator, To increase the pressure, turn the knob clockwise and to decrease the pressure turn the knob counterclockwise, @ Oil Fill Cap Tank Safety Valve Used to allow excess tank pressure to escape valve should only open when the tank pressure is above the maximum rated pressure. Sight Gauge Tube Pressure Switch This controls the power to the motor and also the cutdn/cut-out pressure settings. This switch serves as the Auto-On/Off positions for the unit. Pressure Relief Valve The pressure relief valve, located on the side of the pressure switch, is designed to automatically release compressed air when the air compressor reaches cut-out pressure. The released air should only escape momentarily and the valve should then close. Pressure Relief Tube Check Valve When the pump is not in operation, the valve closes to retain air pressure inside the tank. An internal component. Installation & Assembly The air compressor should be turned off, unplugged from the power source, the air bled from the tank and the unit allowed time to cool before any maintenance is performed, Personal injuries could occur from moving parts, electrical sources, compressed air or hot surfaces, The quick connect assembly must be attached before use, Failure to assemble correctly could result in leaks and possible injury, if unsure of assembly instructions or you experience difficulty in the assembly please call our toll free number for assistance, Assembly 1, Remove air compressor, manual, air filter assembly, and accessories from packaging, 2, Remove the plastic plug from the compressor intake port, (see diagram below) 3, Install the filter in the compressor intake port, (see diagram be!ow) 4, Remove the oil fiii cap from the crankcase and fiii until the oil reaches the top of the red dot in the sight glass, Oil capacity is 3 oz, (seebelow)Use SAE°30 non-detergent (API CG/CD heavy duty motor oil), Under extreme cold weather conditions use SAE°10 weight oil, 5, Replace the oil cap, Estimated Assembly Time: Approximately 5 minutes Getting Started _ Location of the Air Compressor The air compressor should always be located in a clean, dry and well ventilated environment, The unit should have at minimum, 12 inches of space on each side, The air filter intake should be free of any debris or obstructions, Check the air filter on a daily basis to make sure it is clean and in working order, Grounding Instructions This product should be grounded, in the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current, This product is equipped with a cord having a grounding wire with an appropriate grounding plug, (See the figure below,) The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances, Check with a qualified electrician or service personnel if these instructions are not completely understood or if in doubt as to whether the tool is properly grounded, installation of the grounding plug wiii result in a risk of electric shock, if repair or replacement of the cord or plug is necessary, do not connect the grounding wire to either fiat blade terminal, The wire with insulation having an outer surface that is green with or without yellow stripes is the grounding wire, Check with a qualified electrician or serviceman if the grounding instructions are not completely understood, or if in doubt as to whether the product is properly grounded, Do not modify the plug provided, if it will not fit the outlet, have the proper outlet installed by a qualified electrician, This product is for use on a circuit having a nominal rating of 120 volts and is factory-equipped with a specific electric cord and plug to permit connection to a proper electric circuit, Make sure the product is connected to an outlet having the same configuration as the plug, An adapter should not be used with this product, if the product must be reconnected for use on a different type of electric circuit, qualified service personnel should make the reconnection, Extension Cords Use only a 3°wire extension cord that has a 3°blade grounding plug and a 3°slot receptacle that will accept the plug on the product, Make sure your extension cord is in good condition, When using an extension cord, be sure to use one heavy enough to carry the current your product will draw, Cords must not exceed 25 feet and No, 12 AWG size must be used, An undersized cord will cause a drop in line voltage resulting in loss of power and overheating, Break In Procedures No break in procedure is required by the user, This product is factory tested to ensure proper operation and performance, Grounded Outlet Grounding Pin 4 Operating Procedures Dally Start-Up Procedures 1, Set the Auto-On/Off lever to the Off position, 2...