Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
The outlet must have the same configuration as the plug. See illustration. DO NOT USE AN ADAPTER. MWIlllfl IMPROPER GROUNDING CAN RESULT IN SEVERE ELECTRICAL SHOCK. Inspect the plug and cord before each use. Do not use if there are signs of damage. Do not modify the plug that has been provided. If it does not fit the available outlet, the correct outlet should be installed by a qualified electrician. If these grounding instructions are not completely understood, or if in doubt as to whether the compressor is properly grounded, have the installation checked by a qualified electrician. EXTENSION CORDS Use extra air hose instead of an extension cord to avoid voltage drop and power loss to the motor. If an extension cord must be used, be sure it is: • A 3-wire extension cord that has a 3-blade grounding plug, and a 3-slot receptacle that will accept the plug on the compressor. • In good condition. • No longer than 50 feet. • 12 gauge (AWG) or larger. (Wire size increases as gauge number decreases.) 10 AWG and 8 AWG may also be used. DO NOT USE 14 AWG or SMALLER. ADDITIONAL REGULATORS AND CONTROLS Since the air tank pressure is usually greater than that which is needed, a regulator is employed to control the air pressure ahead of any individual air driven device. Separate air transformers which combine the function of air regulation, moisture and dirt removal should be used where applicable. LUBRICATION The bearings in this unit are sealed bearings which contain sufficient lubricant to last their lives. No other lubrication is required. BREAK-IN PROCEDURES NOTE: Serious damage may result if the following break-in instructions are not closely followed. This procedure is required: Before the air compressor is put into service, after replacing the check valve, and when the piston or the cylinder sleeve is replaced. a. Set the pressure switch lever to the “OFF” position. b. Plug the power cord into the correct branch circuit receptacle. 8 c. Turn the drain valve (J) Fig, 2, opening it fully, to prevent air pressure build-up in the tank. d. Move the pressure switch lever to “ON/AUTO”. The compressor will start. e. Run the compressor for 15 minutes. Make sure the drain valve is open and there is no tank pressure build-up. f. After 15 minutes, close the drain valve by turning knob. The air receiver will fill to cut-out pressure and the motor will stop. The compressor is now ready for use. OPERATING PROCEDURES Preparation for Use: 1. Before attaching air hose or accessories, make sure the OFF/AUTO lever is set to “OFF” and the air regulator is closed. 2. Inspect air intake filter (H) Fig. 1. Clean or replace as necessary. 3. Attach hose and accessories. ikWARNING TOO MUCH AIR PRESSURE CAUSES A HAZARDOUS RISK OF BURSTING. CHECK THE MANUFACTURER’S MAXIMUM PRESSURE RATING FOR AIR TOOLS AND ACCESSORIES. THE REGULATOR OUTLET PRESSURE MUST NEVER EXCEED THE MAXIMUM PRESSURE RATING OF THE TOOL BEING USED. 4. Turn the OFF/AUTO lever to “AUTO” and allow tank pressure to build. Motor will stop when tank pressure reaches “cut-out” pressure. 5. Open the regulator by turning it clockwise. Adjust the regulator to the correct pressure setting. The compressor is ready for use. 6. Always operate the air compressor in well ventilated areas; free of gasoline or other solvent vapors. Do not operate the compressor near the spray area. After Use: 7. Set the “OFF/AUTO” lever to “OFF”. 8. Turn the regulator counterclockwise to set the outlet pressure to zero. 9. Remove the air tool or accessory. 10. Pull ring on safety valve (K) Fig. 3, allowing air to bleed from the tank until tank pressure is approximately 20 psi. Release safety valve ring. 11. Drain water from air tank. Turn drain valve (J) Fig. 2, counterclockwise, to open. ■WW-'ina WATER WILL CONDENSE IN THE AIR TANK. IF NOT DRAINED, WATER WILL CORRODE AND WEAKEN THE AIR TANK CAUSING A RISK OF AIR TANK RUPTURE. NOTE: If drain valve is plugged, pull ring on safety valve (K) Fig. 3, and hold until all air pressure has been released. The valve can then be removed, cleaned, and reinstalled. 12. After the water has been completely drained, turn drain valve to close. The air compressor can now be stored. a MAINTENANCE KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. Inspect air intake filter and clean or replace as necessary. Clean all plastic parts with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. rYffl'HL*!! WEAR SAFETY GLASSES WHILE USING COMPRESSED AIR. FAILURE TO START Should your tool fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line. SERVICE AND REPAIRS All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These operations should ONLY be performed by either an AUTH...
Ce manuel est également adapté pour les modèles :matériel de pompage - CF1540 (3.69 mb)
matériel de pompage - CF2400 (3.69 mb)