Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
4. AIR TANK PRESSURE GAUGE: The tank pressure gauge provides a reading of the air pressure inside of the compressor tank. 5. PRESSURE REGULATOR: The regulator allows you to select the amount of air pressure that is output through the air hose into tools and accessories. Turn the pressure regulator knob clockwise to increase discharge pressure, and counter clockwise to decrease discharge pressure. Please refer to the air delivery requirements of your tools for the proper pressure settings. NOTICE: Be careful not to over tighten pressure regulator knob when it “bottoms out” as this may damage pressure regulator. 6. OUTLET PRESSURE GAUGE: The outlet pressure gauge provides a reading of the air pressure at the outlet side of the regulator. This pressure is controlled by the pressure regulator and is always less than or equal to the air tank pressure. 7. AIR OUTLET PORT: The air outlet port is located on the pressure regulator body. This port is threaded to accommodate standard 1/4" NPT (M) air fittings found on air hoses and quick connectors. Use PTFE thread-sealing tape on the threads to make sure you have an airtight connection. 8. SAFETY RELIEF VALVE: This compressor is equipped with a safety relief valve that is designed to prevent system failures by relieving pressure from the system when the air pressure reaches a predetermined level. The safety relieve valve is preset by the manufacturer - DO NOT attempt to modify or remove the safety relief valve. 9. AIR TANK DRAIN VALVE: Moisture is produced whenever air is compressed. It is critical to drain water from the air tank on this compressor frequently. If unit is used only occasionally, tank should be drained after each use and prior to the next use. To drain the tank, slowly open the tank drain fitting by turning clockwise. Once all moisture has drained out, close the fitting securely. NOTE: Air tank will not pressurize while drain valve is open. 10. AIR INTAKE FILTER: This compressor is equipped with an externally accessible air intake filter that is designed to clean air coming into the pump. The filter element is easily removed for periodic cleaning with warm soapy water. Rinse the filter and air dry before reinstalling. Replace filter element when necessary. NOTICE: Remove air inlet dust plug and install air filter as indicated in assembly instructions before using air compressor. 11. THERMAL SHUTDOWN SWITCH: The electric motor is equipped with an automatic thermal overload protector. If the unit is overheating, the motor will automatically shut down. Turn the unit off and allow the unit to cool for approximately 20 minutes before turning the unit back to the “I” (ON) position. NOTICE: This air compressor is designed for household use only and is not intended to operate heavy-duty air tools. If your application's demands exceed the capacity of this air compressor, a larger air compressor that is matched to your application is recommended. If the unit shuts down again, please call factory customer service at 1-800- 423-3598 for assistance. 12. HANDLE: Convenient handle for easy transport. 13. WHEELS: Large diameter wheels for easy mobility. ASSEMBLY INSTRUCTIONS STEP 1 - INSTALLING WHEELS AND RUBBER FEET THE WHEELS AND HANDLE DO NOT PROVIDE ADEQUATE CLEARANCE, STABILITY OR SUPPORT FOR PULLING THE UNIT UP AND DOWN STAIRS OR STEPS. THE UNIT MUST BE LIFTED, OR PUSHED UP A RAMP. 8 WARNING WARNING IT MAY BE NECESSARY TO BRACE OR SUPPORT ONE END OF THE AIR COMPRESSOR WHEN ATTACHING THE WHEELS AND THE RUBBER FEET, BECAUSE THE AIR COMPRESSOR WILL HAVE A TENDENCY TO TIP. Installing Wheels: The wheels must be installed prior to operating the compressor. 1. Insert supplied wheel bolt through hole in center of wheel. 2. Place the end of the bolt on the wheel subassembly through the corresponding hole in the wheel ground iron located on the base of the air tank. 3. Slide lock washer over end of wheel bolt. 4. Fasten the wheel in place by threading supplied nut onto the wheel bolt. 5. Repeat steps 1 through 4 above to install second wheel. To Install Rubber Feet: 1. Slide washer over screw and insert into cup shaped end of rubber foot pad. 2. Insert exposed end of bolt into corresponding hole in ground iron. 3. Place washer over the end of the screw. 4. Fasten the rubber foot in place by threading nut onto the end of the mounting screw. 5. Repeat steps 1 through 4 above to install second rubber foot pad. STEP 2 - INSTALLING HANDLE To Install Handle: The horizontal handle receivers are installed at the factory and are permanently attached to the air tank. 1. Slide foam grip so that it is centered over end of horizontal handle crosspiece. 2. Position the horizontal handle crosspiece over the tops of the handle receivers, lining up the openings in the crosspiece pipe with the openings of the handle receiver tubes. 3. Slide the crosspiece ends into the handle receiver tubes and secure in place using the four (4) bolts supplied. STEP 3 - INSTALLING AIR FILTER To Install Ai...