RAB71 16-1/4" Min. H x 42-1/4" Min. W RAB71 available in 16, 24, 28" and 31" depths RAB77 16-1/2" Min. H x 42-3/8" Min. W Electrical Wiring All wiring, including installation of receptacle, must be made in accordance with local electrical codes and regulations. Note: Aluminum wiring may pose special problems - consult a qualified electrician. Grille Options Stamped Aluminum Grille - RAG60 Exterior Architectural Louvers Durable Polycarbonate: RAG61 or RAG64 (Beige) RAG63 or RAG66 (Bittersw

When determining closet depth, note that plenum may protrude into closet up to 4 inches, depending on exterior wall depth. Sides • Allow 3 inches on each side of unit. • For side access closets only: Allow 5 inches clearance to front of unit. Platform • An 8”-12” high, field-supplied platform is recommended for drain access. 230/208 Volt Line Cord Connected Units Power Connection Kit RAK3152 RAK3202 RAK3302 Heater KW 2.55 3.45 5.00 Min. Circuit Amps 15 20 30 Recommended Protective De

Circuit Protection (Amps) RAK3153 8,600/7,100 2,550/2,090 11.6/10.6 15 RAK3203 11,700/9,600 3,450/2,820 15.5/14.1 20 RAK3303 17,000/13,900 5,000/4,090 22.3/20.3 30 230/208 Volt Sub-Base Connected Units Sub-Base Electric Heat (Btuh) Electric Heater Watts Electric Heat Amps Min. Circuit Protection (Amps) RAK204D15P 8,600/7,100 2,550/2,090 11.6/10.6 15 RAK204D20P 11,700/9,600 3,450/2,820 15.5/14.1 20 RAK204D30P 17,000/13,900 5,000/4,090 22.3/20.3 30 Specification Revised 4/06 390565

Installation must comply with local electrical codes and regulations. Power Connection kits required on all Zoneline chassis. For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000. 230/208 Volt Line Cord Connected Units Line Cord Kit Electric Heat (Btuh) Electric Heater Watts Electric Heat Amps Min. Circuit Protection (Amps) RAK3153 8;600/7;l00 2;550/2;090 11.6/10.6 15 RAK3203 ll;700/9;600 3;4

Date of Purchase: Installation: Current Readings at Startup: Single Phase: Three Phase – 1st Phase: 2nd Phase: 3rd Phase: Table of Contents SUBJECT PAGE Safety Instructions................................................................. 2 Description and Specifications ............................................. 2 Lifting of Pump ..................................................................... 2 Sliderail System .................................................................... 2 Pipin

When determining closet depth, note that plenum may protrude into closet up to 4 inches, depending on exterior wall depth. Sides • Allow 3 inches on each side of unit. • For side access closets only: Allow 5 inches clearance to front of unit. Platform • An 8”-12” high, field-supplied platform is recommended for drain access. 230/208 Volt Line Cord Connected Units Power Connection Kit RAK3152 RAK3202 RAK3302 Heater KW 2.55/2.09 3.45/2.83 5.00/4.10 Min. Circuit Amps 15 20 30 Recommende

A - 42-1/8, B- 13-7/8, C - 16-1/4 Maximum Cord Extension (in inches) Wall Opening Dimensions Add 1/4” to A and C dimensions for all cut-out size. RAB71 16-1/4" Min. H x 42-1/4" Min. W RAB71 available in 16, 24, 28" and 31" depths RAB77 16-1/2" Min. H x 42-3/8" Min. W Electrical Wiring All wiring, including installation of receptacle, must be made in accordance with local electrical codes and regulations. Note: Aluminum wiring may pose special problems - consult a qualified electrician. Gr

..CENTRIFUGAL PUMPS WITH X-, XB-OR XC-FRAMES MOTOR ADAPTERS WITHOUT BEARING FRAME TABLE OF CONTENTS Page 1.0 INTRODUCTION 1 2.0 TONKAFLO SPECIFICATIONS 2 2.1 Capacities 2 2.2 Maximum Developed Boost Pressure 3 2.3 Maximum Recommended Operating Temperature 3 2.4 Standard Materials of Construction 3 2.5 Special Materials of Construction 3 2.6 Pump Nomenclature 4 2.7 Special Liquids 4 3.0 PUMP INSTALLATION 5 3.1 Inspection 5 3.2 Pump Mounting and Location 5 3.3 Inlet and Discharge Piping and Connec

RAK40 - Deflector Kit to adapt chassis for use with existing exterior architectural louvered grilles. Electrical Connection 230/208 volt units may be plugged into a receptacle. 265 volt units are provided with a junction box and require direct connection. (NEC Requires 265V Direct Connection) See Architects and Engineers Design Data Manual for electrical connection information including use of sub-base for direct connected units. Installation must comply with local electrical codes and regulat

The controller is mounted in a NEMA 4X enclosure and suitable for indoor or outdoor applications within temperatures of 14°F (-10°C) to 122°F (50°C). The controller should never be mounted in direct sunlight or high-temperature locations as this will cause shortened capacitor life and unnecessary tripping of the overload protector. The controller enclosure is designed for vertical upright mounting only. Mounting in other positions will affect its operation. The controller must be electrically wi