INSTRUCTIONS Displacement Pump 1000 psi (70 bar, 7 MPa) Maximum Working Pressure Model 210–208, Series F 308–043 Rev. F Supersedes Rev. C and PCN D GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441 COPYRIGHT 1990, GRACO INC. Graco Inc. is registered to I.S. EN ISO 9001 Table of Contents Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Setup/Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 . .......................................

Piston (Fig. 1) 1. Remove the intake valve as explained in Intake Valve. 2. Pull the cylinder (38) down, off the piston assembly. 3. Unscrew the piston retainer screws (25). Remove the piston parts from the displacement rod (36). 4. Clean all parts thoroughly, and inspect them for wear or damage. Replace parts as needed. 5. Place the gasket (49) and ball (16) on the piston retainer (43). Install these parts in the displacement rod. NOTE: The piston retainer (43) must not obstruct the ports in th

180 psi (1.2 MPa, 12.4 bar) Maximum Air and Fluid Working Pressure Oil Pumps Model No. 222051, Series E Universal Pump Model No. 222103, Series E 55-Gallon Drum, Bung-Mount Pump Model No. 222104, Series E 275-Gallon Tank, Bung-Mount Pump 307906V CAUTION These pumps are designed to pump lubricating fluids only. Models 222103 222104 Model 222051 05939B 05940B Important Safety instructions Read all warnings and instructions in this manual. Save these instructions. See page 2 for Table of Contents.

1 Y W 06431 . . Installation Mount the pump to suit the type of installation planned. Pump dimensions and mounting hole layout are shown on page 14. CAUTION The hydraulic supply system must be kept clean at all times to avoid damage to the motor and hydraulic power supply. Blow out all hydraulic lines with air and flush thoroughly with compatible solvent before connecting the lines to the motor. Always plug the hydraulic inlets, outlets, and lines when disconnecting them for any reason, to avoid

*3 *4 0805 0806 LUBRICATE PACKINGS 0805 *19 *4 18* 18* *3 (Rectangle comment Karen Scherer 26.05.2004 23:58:46 blank) (Rectangle comment Karen Scherer 26.05.2004 23:59:16 blank) . . Technical Data WARNING Be sure that all fluids and solvents used are chemically compatible with the Wetted Parts listed below. Always read the manufacturer’s literature before using fluid or solvent in this pump. Category Data Maximum fluid working pressure 28.3 MPa, 283 bar (4100 psi) Maximum air input pressure 0.7

241594 Pump, Series B, 10:1 Ratio, with Falcon Air Motor 1500 psi (10.3 MPa, 103.5 bar) Maximum Fluid Working Pressure 150 psi (1.0 MPa, 10.4 bar) Maximum Air Input Pressure Part No. 241595 Pump, Series B, 20:1 Ratio, with Falcon II Air Motor 2200 psi (15 MPa, 152 bar) Maximum Fluid Working Pressure 100 psi (0.7 MPa, 7 bar) Maximum Air Input Pressure Chinese Patent No. ZL00808468.8 Taiwan Patent R.O.C. New Invention Patent No. 163401 U.S. Patent No. 7,168,856 France Brevet No. 1192362 Germany DB

C First choice when quality counts. This gun and hose for Delta Spray Air Spray package or Delta Spray HVLP package This gun and hose for PRO 3500sc Electrostatic package INSTRUCTIONS–PARTS LIST INSTRUCTIONS This manual contains important warnings and information. READ AND KEEP FOR REFERENCE. ACETAL HUSKY 307, WALL-MOUNT PUMP, DRUM SUCTION PRO/ Delta Spray Packages Metal fluid fittings and hose couplings are stainless steel. 100 psi (0.7 MPa, 7 bar) Maximum Fluid Working Pressure 100 psi (0.7 M

CAUTION: In order to avoid damaging the compressor, do not allow the unit to be tilted more than 10° when operating. (2) Place this compressor at least 12 inches away from obstacles that may prevent proper ventilation. Do not place this compressor in an area: . where there is evidence of oil or gas leaks. . where flammable gas vapors or materials may be present. . where air temperatures fall below 14°F (–10°C) or exceed 104°F (40°C). . where extremely dirty air or water could be drawn into this