This screen is a sample. 8 Windows 98 7 Select [OK], then select [OK]. Select [Yes]. The computer will restart. 9 Select on the taskbar, select [Password]: The following screen is displayed. 10 Input [wdsp], then select [OK]. 11 Select [Connect] on of the step 3 . The wireless display can be used. 12 Windows 98 Power off your computer. 13 Windows 98 Remove the external mouse, then turn on your computer again. 14 Windows 98 Do not remove the port replicator until step 15 is completed. NOTE When [Windows did not detect a mouse attached to the computer] is displayed, add the check mark for [Do not show this message in the future] through the external keyboard. (Press Alt + D , press Tab ,then press Enter .) 15 Windows 98 Power off your computer through the keyboard. ( page 27) 16 Select on the taskbar, select [Run Setup Utility]. The following screen is displayed. Getting 21 First-time Operation Getting Started 17 Input [wdsp], then select [OK]. The following screen is displayed. 18 Set the necessary items, select [Next]. This screen is a sample. The following screen is displayed. 19 Select on the taskbar, set the parameters in [Configuration] or [Encryption]. 20 Select on the taskbar, select [Password]. Set the password by following screen. 21 Select [Next] at the screen. The following screen is displayed. This screen is a sample. NOTE After this, if [Connection Timeout] is displayed, select [OK]. This screen is a sample. 22 Windows 98 Windows 98 Select [Start] - [Settings] - [Control Panel] - [Network] - [TCP/IP PRISM2 IEEE 802.11 PC CARD Adapter] - [Properties] - [IP Address], set the parameters by following the above screen, then select [OK]. Windows 2000 Select [Start] - [Settings] - [Control Panel] - [Network and Dial-up Connections] -[Local Area Connection 2] - [Properties] -[Internet Protocol (TCP/IP)] [ Properties], set the parameters by following the above screen, then select [OK]. 23 Restart the computer. Windows 98 Be sure to prepare the following. • Optional port replicator (CF-VEB071) • External keyboard • External display When using the files in the following folders available on the retail version of the Windows CD-ROM, it is necessary to run a separate file decompression program. \tsclient \tools To uncompress the file, it is necessary to have approximately 80 MB of free disk space available on the hard disk. To use the CD-ROM drive in MS-DOS mode, perform the operation below after modifying config.sys and autoexec.bat ( “CD-ROM Drive”). File decompression method: 1 Turn on your computer. 2 When [Press to enter SETUP] is displayed, immediately press Ctrl (until the menu is displayed). 3 Select [Command prompt only]. 4 Insert the Product Recovery CD-ROM. 5 At the prompt, input the following: L:\en\addfile Enter Follow the message on the screen. After this program is executed, the contents of the above folders will be decompressed to the c:\util\win98add folder. Windows 2000 When a new device has been installed or a new Windows Component has been added in [Start] - [Settings] - [Control Panel] - [Add/Remove Programs], [Insert Disk] may appear. Select [OK] and specify [c:\winnt\cdimage] in place of [c:\sysprep\i386] or [D:], then select [OK]. e.g. [c:\winnt\cdimage\i386] in place of [D:\i386] NOTE Getting Starting Up/Shutting Down Operation Starting Up Do not maximize the MS-DOS screen. Once maximized, the connection with the wireless display is interrupted. The connection cannot be re-established and the computer no longer operates. In such cases, the computer must be powered off. Data may be lost. CAUTION 1 Turn on your computer Press the power switch and hold it for approximately one second until the power indicator turns on before releasing it. Power Switch Display Status 2 After confirming the display status in-Indicator dicator lit, turn on the wireless display( Operating Instructions of the wireless display) After confirming that the power indicator has turned on, avoid the following until Windows has completed loading. • Connecting or disconnecting the AC adaptor. • Touching the power switch. • Performing any keyboard or external mouse operations. Once the computer is powered off, you must wait at least ten seconds before powering it on again. When the computer is turned on in a low-temperature environment, start-up may take longer than usual, in order to ensure stable operation of the computer’s systems. When the CPU temperature rises, the computer may not power on to prevent the CPU from overheating. Should this happen, allow the computer to cool down then switch the power on again. If the computer still does not power on, contact Panasonic Technical Sup- port. CAUTION If [Enter Password] is displaye...
)
