Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Pull the interposer to detach it from the hard drive. 4. Lift the hard drive cage off the hard drive. Replacing the Hard Drive 1. Remove the new drive from its packaging. Save the original packaging for storing or shipping the hard drive. 2. Replace the hard drive in the bay. l For Hard Drive 1: . Replace the four M3 x 3-mm screws securing the hard drive cage to the hard drive. . Connect the interposer to the hard drive. . Replace the four screws securing the hard drive assembly to the computer base. . Connect the cable with the blue pull-tab to the system board connector. l For Hard Drive 2: . Connect the interposer to the hard drive. . Replace the four M3 x 3-mm screws securing the hard drive cage to the hard drive. . Press the hard drive firmly on to the system board connector. . Replace the four screws securing the hard drive assembly to the computer base. l Replace the base cover (see Replacing the Base Cover). 4. Slide the battery into the bay until it clicks into place. 5. Install the operating system for your computer, as needed (see Dell Technology Guide). 6. Install the drivers and utilities for your computer, as needed (see Dell Technology Guide). Back to Contents Page 1 hard drive 2 interposer NOTICE: When the hard drive is not in the computer, store it in protective antistatic packaging (see "Protecting Against Electrostatic Discharge" in the safety instructions that shipped with your computer.) NOTICE: Use firm and even pressure to slide the drive into place. If you use excessive force, you may damage the connector. NOTICE: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in damage to the computer. Back to Contents Page Keyboard Dell™ Studio 1735/1737 Service Manual Removing the Keyboard Replacing the Keyboard Removing the Keyboard 1. Follow the procedures in Before You Begin. 2. Remove the Center Control Cover (see Removing the Center Control Cover). 3. Ease the keyboard surround up with a plastic scribe. 4. Lift the keyboard surround off the computer. 5. Remove the four screws at the top of the keyboard. 6. Carefully slide the keyboard out of the computer and turn it over as shown in the illustration. Do not pull hard on the keyboard. CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as a connector on the back of the computer). NOTICE: To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the computer. 1 keyboard surround NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and time- consuming to replace. Be careful when removing and handling the keyboard. NOTICE: Be extremely careful when removing and handling the keyboard. Failure to do so could result in scratching the display panel. 7. Release the connector latch that secures the keyboard cable to the connector on the system board and release the cable. 8. Lift the keyboard off the computer. Replacing the Keyboard 1. Slide the keyboard cable into the connector on the system board and pull down on the connector latch that secures the keyboard cable to the system board. 2. Align the tabs along the bottom of the keyboard with the slots of the palm rest and slide the keyboard under the palm rest. 3. Replace the four screws at the top of the keyboard. 4. Align the hooks beneath the keyboard surround and snap it into place. 5. Replace the Center Control Cover (see Replacing the Center Control Cover). 6. Slide the battery into the bay until it clicks into place. Back to Contents Page 1 screw (4) 2 keyboard 3 keyboard tab (6) 4 connector latch 5 keyboard cable NOTICE: The keycaps on the keyboard are fragile, easily dislodged, and time- consuming to replace. Be careful when removing and handling the keyboard. Back to Contents Page Memory Dell™ Studio 1735/1737 Service Manual Removing the Memory Module(s) Replacing the Memory Module(s) You can increase your computer memory by installing memory modules on the system board. See "Specifications" in your Quick Reference Guide for information on the memory supported by your computer. Install only memory modules that are intended for your computer. Your computer has two user-accessible SODIMM sockets that can be accessed from the bottom of the computer. The DIMM B memory module is located directly above the DIMM A memory module located on the bottom of the computer. Removing the Memory Module(s) 1. Follow the procedures in Before You Begin. 2. Turn the computer over and remove the base cover (see Removing the Base Cover). 3. Use your fingertips to carefully spread apart the securing clips on each end ...