Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Use your fingertips to carefully spread apart the metal clips securing each end of the Mini PCI card until the card pops up. Wireless Mini PCI Card 1 2 1 Mini PCI card 2 metal retention clips (2) Remove the Mini PCI card from the connector at a 45-degree angle. Wireless Mini PCI Card Replacing the Mini PCI Card CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1 Follow the instructions in "Preparing to Work Inside the Computer" on page 7 2 Follow the instructions in "Removing the Mini PCI Card" on page 49, as applicable. NOTICE: To avoid damaging the Mini PCI card, make sure the antenna cables are not under the card when you secure the card into place. NOTICE: The edge connector is keyed to ensure correct insertion. If you feel resistance, check the connector and realign the card. 3 Install the new Mini PCI card: a Align the notch in the Mini PCI card edge connector with the tab in the connector slot. b Slide the Mini PCI card firmly into the slot at a 45-degree angle, and then rotate the card down until it clicks into place. If you do not feel the click, remove the card and reinstall it. 1 1 Mini PCI card Wireless Mini PCI Card Connect the antenna cables to the Mini PCI card. Make certain that the cable connectors snap securely into place. 1 1 antenna cables Replace the modem/Mini PCI/wireless cover and tighten the screws. Wireless Mini PCI Card 54 Wireless Mini PCI Card 11 Display Assembly and Display Latch Display Assembly Removing the Display Assembly CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product InformationGuide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1 Follow the instructions in "Preparing to Work Inside the Computer" on page 7. 2 Remove the hinge cover (see "Removing the Hinge Cover" on page 41). 3 Remove the keyboard (see "Removing the Keyboard" on page 43). 4 Open the display all the way (180 degrees) so that it rests flat against your work surface. 5 Use the pull-tab to disconnect the display cable from the system board. 6 Remove the Mini PCI antenna cables from the retaining clips on the base of the computer and pull apart the connectors. 7 Remove the four M2.5 x 5-mm screws (two on each side) that connect the display assembly to the computer. 8 Lift the display assembly straight out of the computer. Display Assembly and Display Latch 55 6 12 4 5 3 1 display assembly 3 antenna cable retaining clips 5 display cable 2 Mini PCI antenna cables 4 antenna cable connectors 6 M2.5 x 5-mm screws (4) Replacing the Display Assembly CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1 Follow the instructions in "Preparing to Work Inside the Computer" on page 7 2 Follow the instructions in "Removing the Display Assembly" on page 55. 3 Align the new display assembly over the screw holes in the base of the computer. 4 Replace the four M2.5 x 5-mm screws (two on each side) to secure the display assembly to the base of the computer. 5 Connect the Mini PCI antenna cable connectors and press the cables into the retaining clips on the base of the computer. 6 Connect the display cable to the system board. Display Assembly and Display Latch 7 Replace the keyboard (see "Replacing the Keyboard" on page 45). 8 Replace the hinge cover (see "Replacing the Hinge Cover" on page 42). Display Bezel Removing the Display Bezel CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1 Follow the instructions in "Preparing to Work Inside the Computer" on page 7. 2 Remove the hinge cover (see "Removing the Hinge Cover" on page 41). 3 Remove the keyboard (see "Removing the Keyboard" on page 43). 4 Remove display assembly (see "Removing the Display Assembly" on page 55). 5 Use a plastic scribe to remove the six rubber bumpers from around the display assembly. It is not necessary to remove the oval bumpers located on the sides of the display. 6 Remove the six M2.5 x 5-mm screws from around the display assembly. NOTICE: To avoid damaging the bezel, carefully separate the bezel from the display assembly by starting along the bottom of th...