Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
6. Replace the keyboard (see Replacing the Keyboard). 7. Replace the hinge cover (see Replacing the Hinge Cover). 8. Replace the hard drive (see Replacing the Hard Drive). 9. Replace the optical drive (see Replacing the Optical Drive). Back to Contents Page Back to Contents Page Display Dell™ Vostro™ 1500 and Inspiron™ 1520/1521 Service Manual Display Assembly Display Bezel Display Panel Display Latch Camera and Microphone Assembly Display Assembly Removing the Display Assembly 1. Follow the instructions in Before You Begin. 2. Close the display and turn the computer over. 3. Loosen the two captive screws that secure the Mini Card compartment cover, then remove the cover and set it aside. 4. Disconnect antenna cables from any installed Mini Cards (see Wireless Mini Cards). 5. Remove the two M2.5 x 8-mm screws from the bottom of the computer. 6. Remove the two M2.5 x 8-mm screws from the back of the computer. 7. Remove the hinge cover (see Removing the Hinge Cover). 8. Remove the keyboard (see Removing the Keyboard). 9. Loosen the captive grounding screw, then disconnect the display cable from the display cable connector on the system board. 10. Disconnect the camera/microphone cable from the camera/microphone cable connector on the system board. 11. Lift the display cable and antenna cables from beneath the tabs on the palm rest. 12. Lift the display assembly out of the computer. CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: Ensure that the display cable and the antenna cables do not get caught beneath the plastic tabs on the palm rest. Replacing the Display Assembly 1. Follow the instructions in Before You Begin. 2. Align the display hinges with the holes in the base of the computer, then lower the display into place. 3. Slide the antenna cables through the hole in the palm rest and the base of the computer. 4. Route the display cable and antenna cables beneath the plastic tabs on the palm rest. 5. Connect the camera/microphone cable to the camera/microphone cable connector on the system board. 6. Connect the display cable to the display cable connector on the system board. 7. Replace and tighten the captive grounding screw. 8. Replace the keyboard (see Replacing the Keyboard). 9. Replace the hinge cover (see Replacing the Hinge Cover). 10. Replace the two M2.5 x 8-mm screws on the back of the computer. 11. Close the display and turn the computer over. 12. Replace the two M2.5 x 8-mm screws on the bottom of the computer. 1 display assembly 2 camera/microphone cable 3 grounding screw 4 antenna cables 5 display cable CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: Ensure that the display cable and antenna cables are properly routed and secured beneath the plastic tabs on the palm rest. 13. Connect the Mini-Card antenna cables (see Wireless Mini Cards). 14. Replace the Mini Card compartment cover and tighten the screws. Display Bezel Removing the Display Bezel 1. Follow the instructions in Before You Begin. 2. Remove the hinge cover (see Removing the Hinge Cover). 3. Remove the keyboard (see Removing the Keyboard). 4. Remove the display assembly (see Removing the Display Assembly). 5. Remove the four rubber display bumpers and two mylar screw covers from around the display bezel. 6. Remove the six M2.5 x 4.2-mm shoulder screws from around the display bezel. 7. Starting at the top corner of the display panel, use your fingers to separate the bezel from the top cover, then lift the inside edges to separate the remainder of the bezel. Replacing the Display Bezel 1. Follow the instructions in Before You Begin. CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. 1 rubber display bumpers (4) 2 M2.5 x 4.2-mm screws (6) 3 mylar screw covers (2) 4 display bezel NOTICE: Removal of the bezel from the display back cover requires extreme care to avoid damage to the bezel. CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. 2. Starting at any corner, use your fingers to gently snap the bezel into place to secure it to the display panel. 3. Replace the six M2.5 x 4.2-mm shoulder screws around the display bezel. 4. Replace the four rubber display bumpers and two mylar screw covers around the display bezel. 5. Replace the display assembly (see Replacing the Display Assembly). 6. Replace the keyboard (see Replacing the Keyboard). 7. Replace the hinge cover (see Replacing the Hinge Cover). Display Panel Removing the Display Panel 1. Follow the instructions in Before You Begin. 2. Remove the hinge cover (see Removing the Hinge Cover). 3. Remove the keyboard (see Removing the Keyboard). 4. Remove the display assembly (see Removing the Display Assembly). 5. Remove the display bezel (see Removing the Display Bezel). 6. Remove the eight M2 x 3-mm screws (f...