Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Follow the instructions in Before You Begin. 2. Remove any cards from the 3-in-1 media card slot. 3. Remove the center control cover (see Removing the Center Control Cover). 4. Remove the keyboard (see Removing the Keyboard). 5. Remove the display assembly (see Display). 6. Turn the computer over and remove any installed memory modules and the WLAN card (see Memory Module and Removing the WLAN Card). 7. Remove the screw from the memory bay. 8. Remove the optical drive (see Removing the Optical Drive). 9. Remove the two screws from the optical drive bay. 10. Remove the ten screws from the computer base. 11. Turn the computer over and remove the two screws from the top of the palmrest. 12. Disconnect the power/keyboard device status light, touch pad, and display hinge connectors from the system board. 13. Starting at the top of the palm rest, use your fingers to separate the palm rest from the computer base by lifting the inside of the palm rest while pulling in on the outside CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: Carefully separate the palm rest from the computer base to avoid damage to the palm rest. Replacing the Palm Rest 1. Align the palm rest with the computer base and gently snap it into place. 2. Reconnect the power/keyboard device status light, touch pad, and display hinge cables to the respective system board connectors. 3. Replace the two screws on the top of the palm rest. 4. Turn the computer over and replace the 13 screws in the computer base. 5. Replace the display assembly (see Replacing the Display Assembly). 6. Replace the memory modules (see Replacing the Memory Module(s)). 7. Replace the card in the 3-in-1 card slot. 8. Replace the WLAN card (see Replacing the WLAN Card). 9. Replace the hard drive (see Replacing the Hard Drive). 10. Slide the battery into the battery bay, until it clicks in place. Back to Contents Page 1 palmrest screw (2) 2 power/keyboard status light cable 3 touch pad cable 4 display hinge cable Back to Contents Page Speaker Dell™ Inspiron™ 1410 Service Manual Removing the Speaker Replacing the Speaker Removing the Speaker 1. Follow the instructions in Before You Begin. 2. Remove the palm rest (see Palm Rest). 3. Remove the screws that secure the speaker to the computer base. 4. Disconnect the speaker cable from the system board connector. 5. Remove the speaker. Replacing the Speaker 1. Connect the speaker cable to the system board connector. 2. Replace the two screws that secure the speakers to the computer base. 3. Follow the instructions in Replacing the Palm Rest. 4. Slide the battery into the battery bay, until it clicks in place. Back to Contents Page CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. 1 speaker 2 speaker screw (2) 3 speaker cable connector Back to Contents Page System Board Dell™ Inspiron™ 1410 Service Manual Removing the System Board Replacing the System Board Removing the System Board The system board's BIOS chip contains the Service Tag, which is also visible on a barcode label on the bottom of the computer. The replacement kit for the system board includes a CD that provides a utility for transferring the Service Tag to the replacement system board. 1. Follow the instructions in Before You Begin. 2. Remove any installed media cards from the 3-in-1 media card slot. 3. Remove any installed memory modules and the WLAN card (see Memory Module and Removing the WLAN Card). 4. Remove the optical drive (see Optical Drive). 5. Remove the center control cover (see Removing the Center Control Cover). 6. Remove the display assembly (see Display). 7. Remove the keyboard (see "Removing the Keyboard). 8. Remove the palm rest (see Palm Rest). 9. Remove the 3-in-1 media card reader. 10. Disconnect the system fan, speaker, RJ-11, and DC-In cables from the system board connectors. 11. Remove the system fan (see Removing the System Fan). 12. Remove the mylar tapes and then remove the four screws from the back of the computer securing the hard disk. 13. Remove the two remaining screws that secure the system board to the computer base. CAUTION: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Complia...