Évaluations - , GPA:
(
)
)
Fabricant : Dell
Taille : 1.91 mb
Nom Fichier :
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
8. Use the pull-tab to disconnect the LED cable, and then disengage the LED cable from the cable channel. 9. Remove the four M2.5 x 5-mm screws (two on each side) that connect the display to the computer base. 1 antenna cables 1 display cable pull-tab 2 M2.5 x 5-mm screws (4) 3 Mini PCI card antenna cables (2) 4 display cable connector on system board 1 LED cable 2 Mini PCI card antenna cables NOTE: When removing the display assembly, carefully thread the Mini PCI card antenna cables through the computer base. 10. Lift the display assembly away from the computer. Replacing the Display Assembly 1. Align the display assembly over the screw holes in the base of the computer. 2. Thread the Mini PCI antenna cables back through the hole in the base of the computer. 3. Replace the four M2.5 x 5-mm screws. 4. Connect the LED cable to the system board. 5. Connect the display cable to the system board. 6. Replace the center control cover. 7. If a Mini PCI card is installed, connect the antenna cables to the card. If one is not installed, tuck the antenna cables to their secured location. 8. Replace the Mini PCI card cover. Display Bezel Removing the Display Bezel 1. Follow the instructions in "Before Working Inside Your Computer." 2. Remove the display assembly. 3. Remove the six screw-cover/rubber display bumpers. 4. Remove the two screw covers and the four shoulder screws. 5. Remove the four M2.5 x 5-mm screws at the corners of the display. 6. Use your fingers to separate the bezel from the top cover by pulling the lower-right corner of the bezel down toward the bottom edge (A) of the display assembly to clear the tab on the bottom of the lower-right corner. Then pull the bezel toward the right side of the display assembly to clear the tab on the side (B) of the lower-right corner. 1 M2.5 x 5-mm screws (4) 2 screw covers (2) 3 rubber display bumpers (6) 4 shoulder screws (2) CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer. NOTICE: Removal of the bezel from the top cover requires extreme care to avoid damage to the bezel. 7. Repeat step 6 for the lower-left corner of the bezel. Then use your fingers to release the snaps around the rest of the bezel and lift it away from the cover. Replacing the Display Bezel 1. Starting at any corner, use your fingers to gently snap the bezel into place to secure it to the display panel. 2. Replace the four M2.5 x 5-mm screws on the front of the bezel. 3. Replace the four shoulder screws and two screw covers. 4. Replace the six screw-cover/display bumpers around the display assembly. Display Panel 1 tabs 1 display bezel 2 display panel Removing the Display Panel 1. Follow the instructions in "Before Working Inside Your Computer." 2. Remove the display assembly. 3. Remove the display bezel. 4. Remove the M2 x 3-mm ground screw that attaches the display-panel ground wire to the back display cover. 5. Remove the eight M2 x 3-mm screws (four on each side of the display panel). 6. Lift the display panel out of the display cover. 7. Press in both sides of the top flex-cable connector, and pull the top flex-cable connector away from the display connector. 8. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector. Replacing the Display Panel 1. Reconnect the top display cable connector to the top flex-cable connector. 2. Reconnect the bottom flex-cable connector to the inverter connector. 3. Replace the display panel inside the top cover. 4. Replace the M2 x 3-mm ground screw that attaches the display-panel ground wire to the back display cover. 5. Replace the eight M2 x 3 screws (four on each side) around the display panel. 1 display grounding screw 2 display 3 M2 x 3-mm screws (8) 4 display back cover CAUTION: Before you begin the following procedure, see the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer. NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer. 1 pull-tab on bottom flex-cable connector 2 top flex-cable connector 3 display connector 4 inverter connector 6. Replace the display bezel. Display Latch Removing the Display Latch 1. Follow the instructions in "Before Working Inside Your Computer." 2. Remove the display. 3. Remove the display bezel. 4. Slide the latch to the right and gently lift up. 5. Remove the spring that attaches the latch to the display panel. Replacing the Display Latch 1. Replace the spring that attaches the latch to the display panel...