Évaluations - 2, GPA: 4.5 ( )

Fabricant : Petsafe Taille : 1.75 mb Nom Fichier : Langue d'enseignement:

Lift the rubber dust cover protecting the Handheld Transmitter Charging Jack. 2. Connect one of the charger connectors to the Handheld Transmitter Charging Jack (1A). 3. Plug the charger into a standard wall outlet. The Red LED will light up. When fully charged, the LED will change to Green. 4. When charging is complete, be sure to replace the rubber dust cover. Note: Approximate battery life between charges is 40 to 60 hours, depending on frequency of use. The Transmitter has two LED’s used to indicate the selected dog. The Dog 1 Red LED is on the left when holding the unit with the LED’s facing the operator, and the Dog 2 Green LED is on the right. The transmitter is factory set in single dog mode. To verify, press and release the Dog Select Button multiple times. (The Red LED will blink once for each press and release.) Transmitter Indicators 1A Condition Red LED Normal Operation OFF Low Battery - press and release any blue correction button 3 flashes every 5 seconds Dog 1—any blue correction button ON length of any blue correction button press. If a Static Stimulation button is held up to 12 continuous seconds, then a rapid flash will indicate a safety time-out. Charging ON Condition Green LED Normal Operation OFF Dog 2—any blue correction button ON length of any blue correction button press. If a Static Stimulation button is held up to 12 continuous seconds, then a rapid flash will indicate a safety time-out. Charging Complete ON StepPrepare the Receiver Collar 2 2 Charge the Receiver Collar 1. Lift the rubber dust cover protecting the Receiver Collar Charging Jack. 2. Connect one of the charger connectors to the Receiver Collar Charging Jack (2A). 3. Plug the charger into a standard wall outlet. The Red LED will light up. When fully charged, the LED will change to Green. 4. When charging is complete, be sure to replace the rubber dust cover. To Turn the Receiver Collar On 1. Press and hold the On/Off Button (2B) until the Green LED light comes on. (This takes 2A approximately one second.) 2. Release the On/Off Button. In normal mode, the Green LED will flash once every 5 seconds, indicating the Receiver Collar is on and ready to receive a radio signal from the Handheld Transmitter. To Turn the Receiver Collar Off 1. When you press the On/Off Button, the Red LED light will come on. Hold down the button until the Red LED turns off (approximately 5 seconds). 2. Release the On/Off Button. To extend the life between charging cycles, turn the Receiver Collar off when it is not in use. Approximate battery life between charges is 15-20 hours, depending on frequency of use. Receiver Indicators On/Off Button 2B Condition Red LED Normal Operation - Low Battery 3 flashes every 5 seconds Correction ON while delivering correction Charging ON Condition Green LED Pairing Mode Flashes once every second Normal Operation - Good Battery Flashes once every 5 seconds Charging Complete ON Customer Care Center 1-800-732-2677 Rechargeable Batteries • The rechargeable Nickel Metal Hydride (NiMH) batteries are not memory sensitive and do not require depletion before charging. • The batteries come partially charged from the factory, but will require a full charge (up to 12 hours) before the first use. • If your equipment has not been charged for an extended period, you may experience a decrease in battery life the first few uses. Afterwards, the battery life will return to previous capacity levels. • You should expect many years of battery life from the rechargeable batteries before replacement. Please contact Customer Care for replacement batteries. StepFit the Receiver Collar 3 3 Important: The proper fit and placement of your Receiver Collar is important for effective operation. The Contact Points must have direct contact with your dog’s skin on the underside of his neck. To assure a proper fit, please follow these steps: 1. Make sure that the Receiver Collar is turned off. 2. Start with your dog standing comfortably (3A). 3. Place the Receiver Collar on your dog’s neck close to the ears. Center the Contact Points underneath your dog’s neck, touching the skin (3B). Note: It is sometimes necessary to trim the hair around the Contact Points to make sure that contact is consistent. 3A Do not shave the pet’s neck as this may increase the risk of skin irritation. 4. Check the tightness of the Receiver Collar by inserting one finger between the collar and your dog’s neck (3C). The fit should be snug but not constricting. 5. Allow your dog to wear the Receiver Collar for several minutes then recheck the fit. Check the fit again as your dog becomes more comfortable with the Receiver Collar. To Prevent Skin Irritation From Occurring 3B3C Risk of skin damage. For comfort, safety and effectiveness of this product, please ensure that you check the fit of your pet’s collar frequently. If any skin irritation is observed, discontinue the use of the collar for a few days. If the condition persists beyond 48 hours, see your ve...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :