Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
With rotating floor brush removed from vacuum cleaner (Steps 1-4 of "Check rotating floor brush and drive belt"), grasp old drive belt and remove from motor pulley. Discard old drive belt. 3. Place new drive belt over motor pulley and stretch other end over rotating floor brush in the space between the bristles. 4. Place ends of rotating floor brush down into slots on sides as shown. 5. Turn rotating floor brush by hand several times in direction of motor pulley. If properly installed, drive belt will center itself on rotating brush. 6. Reposition brush cover and replace two screws. Make sure end of brush cover is snapped into place. Brush Cover Air Passageway Brush Cover 11 Maintenance and care Maintenance and care Replace light bulb 1. Unplug cleaner from electrical outlet. 2. Using a flat screwdriver, table knife or coin, insert into the slot on the right of the lens and gently push inner latch to the left, as shown, to remove the lens. 3. Remove the bulb from the socket by grasping bulb and pulling straight out. Install the new bulb by pushing it gently into the socket until the bulb snaps into place. 4. Reposition lens by inserting tab on left side and then pushing the right side back into place. Clearing clog Low suction, poor pickup or no suction may be due to a clog in the vacuum cleaner. If you notice a change in the sound of the vacuum motor or a reduction in the spinning action in the dirt container, check for clogs. 1. Unplug cleaner from electrical outlet. 2. Empty dirt container. 3. Check upper tank and primary separator for build up or clogs. Check to make sure primary separator is installed correctly. To unlock the primary separator, grasp the rim and turn toward the left. Pull straight down to remove. If the primary separator is missing or not locked into place, check and clear the tube in the center of the dirt container and properly install primary separator. 4. Remove the Twist ‘n Snap hose from the vacuum by turning to the left. Check the suction inlet, hose and hose wand for clogs. Remove any clogs from the hose using a long, narrow object such as a broomstick. 5. Check the foot hose for clogs. If needed, remove the screw attaching the hose wand base to the vacuum. Straighten the foot hose and unclog with a long, narrow object such as a broomstick. 6. If the clog persists, follow the instructions for checking the rotating floor brush on page 11 and inspect the air passageway for obstructions. 12 FPO Primary Separator Suction Inlet Hose Wand Base Air Passageway Troubleshooting WARNING: To reduce the risk of electric shock, turn power OFF and disconnect plug from electricaloutlet before performingmaintenance or troubleshooting. Vacuum cleaner won’t turn Possible causes Remedies 1. Power cord not firmly plugged in 1. Check electrical plug Vacuum cleaner won't pick up dirt Possible causes Remedies 1. Incorrect height adjustment 1. Adjust powerfoot to correct height setting 2. Hose not attached to suction opening 2. Grasp Quick Release handle and firmly push hose wand onto the suction opening. 3. Twist 'n Snap hose not securely attached 3. Make sure Twist 'n Snap hose is snapped into locked position 4. Crack or hole in hose 4. Check hose and replace if needed 5. Broken or worn drive belt 5. Replace drive belt, see page 11 6. Rotating floor brush bristles worn 6. Replace brush 7. Rotating floor brush jammed 7. Remove brush and clean debris from brush ends 8. Clog in vacuum 8. Follow instructions for clearing clogs on page 12 9. Dirt container full 9. Empty dirt container 10. Dirt container not installed properly 10. Position correctly and lock in place 11. Filters are dirty 11. Check and clean inner and outer circular filters and , pre-motor filter, replace post-motor filter 12. Primary separator missing or installed incorrectly 12. Check for a clog in the tube in the center of the dirt container, clear and properly install primary separator 13. TurboBrush is clogged or debris is 13. Maintain TurboBrush, see page 10 wrapped around the brush Tools won't pick up dirt Possible causes Remedies 1. Crack or hole in hose 1. Check hose and replace if needed 2. Vacuum hose, wand or tools clogged 2. Follow instructions for clearing clogs on page 12 3. Dirt container full 3. Empty dirt container 4. Dirt container or upper tank not installed properly 4. Position correctly and lock in place 5. Filters are dirty 5. Check and clean inner and outer circular filters and , pre-motor filter, replace post-motor filter 6. Primary separator missing or installed incorrectly 6. Check for a clog in the tube in the center of the dirt container, clear and properly install primary separator Vacuum cleaner difficult to push Possible causes Remedies 1. Incorrect height adjustment 1. Adjust powerfoot to correct height setting Visible dirt escaping from cleaner Possible causes Remedies 1. Dirt container full 1. Empty dirt container 2. Filters missing or installed incorrectly 2. Check inner a...