Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
Only those items that are different are labeled. FIGURE 2 NO. REQ’D. PART NO. DECRIPTION 1 1 TUBE 2 1 FOCUSER 3 1 FINDER SCOPE & BRACKET 4 1 12.5MM & 8MM EYEPIECE - 0.96 5 1 LENS CAP 6 1 2X BARLOW-0.96 7 1 FLEX CABLE 8 1 DEC SETTING CIRCLE 9 1 RA SETTING CIRCLE 10 1 EQUATORIAL MOUNT 11 1 TRIPOD HEAD 12 1 COUNTERWEIGHT 13 I COUNTERWEIGHT SHAFT 14 1 ACCESSORY TRAY 15 3 TRIPOD LEG 16 3 TELESCOPE LEG 17 3 RUBBER FEET 18 3 LEG CLAMP 19 PIVOT SCREW 20 3 TRIPOD HINGE SCREW & NUT 21 1 FLEX CABLE 22 1 LATITUDE ADJUSTMENT 23 2 TUBE MOUNTING SCREW 24 3 ALIGNMENT SCREWS 25 1 ALTITUDE SLOW MOTION ROD ASSEMBLY 26 2 ALTITUDE ADJUSTMENT SCREWS 27 Î ALTAZIMUTH MOUNT 2 1. INTRODUCTION Thank you for purchasing this Celestron Newtonian Telescope. This telescope is a precision scientific instrument. With it you will enjoy numerous objects in the sky—planets, nebulae, star clusters, galaxies and other astronomical objects. This manual covers both the equatorial mount models (see Figure 1) and the altazimuth mount models (see Figure 2). The altazimuth mount is the simplest and easiest type of mount to use with two motions — altitude (up and down) and azimuth (side-to-side). The equatorial mount is more expensive and contains setting circles and slow motion cables to make it easier to locate and track astronomical objects. But, before your journey begins take time to read this manual to familiarize yourself with the operation and parts of your telescope. If you have one of the equatorial models or one of the altazimuth models, read all sections that pertain to your telescope. WARNING—NEVER LOOK AT THE SUN WITH YOUR TELESCOPE OR ITS FINDERSCOPE. PERMANENT AND IRREVERSIBLE EYE DAMAGE MAY RESULT AS WELL AS DAMAGE TO YOUR TELESCOPE. HOWEVER, YOU MAY ENJOY LOOKING AT THE SUN IF YOU HAVE A SAFE METHOD OF DOING SO—A SOLAR FILTER. IF USING A SOLAR FILTER, MAKE SURE THE FINDERSCOPE IS COVERED. 2. TELESCOPE ASSEMBLY Please refer to Figure 1 (and the identifying parts list) as you assemble the telescope. The telescope and all items are packed in one box. Included are: Model #31031 Model # 31030 Telescope Optical Tube German Equatorial Mount Adjustable Wood Tripod 5x24 Finderscope and Bracket Counterweight Shaft and Counterweight Tripod Accessory Tray Declination Cable Right Ascension Cable 8mm Eyepiece - lVi" (88x) 12.5mm Eyepiece - 1 Vi" (56x) Barlow Lens - 2x - W* • Telescope Optical Tube • Altazimuth Mount • Adjustable Wood Tripod • 5x24 Finderscope and Bracket • Tripod Accessory Tray • Altitude Slow Motion Rod • 8mm Eyepiece — 1Vi" (88X) • 12.5mm Eyepiece — 1 'A" (56x) Model #31046 Same as #31031 but the eyepieces supplied are: Model# 31030-WOS • 20mm Eyepiece - 1 W (50x) • 6mm Eyepiece - 1 Vi" (167x) Same as #31030 but the eyepieces supplied are: • 20mm Eyepiece — 1 Vi" (35x) • 6mm Eyepiece — 1 Vi" (117x) 3 A. Locate the German equatorial mount or altazimuth mount and the tripod legs along with the tripod mounting hardware and the tripod accessory tray. 1. Lie the tripod head (#11) on its side. Attach the three tripod legs (#15) one by one to the tripod head with the bolts and wing nuts (#20). Do not overtighten the bolts but just make them lightly finger tight. Remember to have each tripod leg in the right orientation with the tripod tray bracket (#14) facing inward. 2. Next, put the bolts and wing nuts in the bottom of the tripod legs through the holes for the height adjustment you want. We suggest you keep it at the lowest height for assembly (you can raise it later if you wish) and for maximum rigidity. NOTE—this may have been assembled at the factory. 3. a) Attach the equatorial mount (#10) to the tripod as shown in Figure 1. b) Attach the altazimuth mount, as shown in Figure 2, to the tripod. 4. Now set the tripod with the equatorial mount attached in the standing position by spreading the legs apart far enough for the tripod accessory tray (#14) to fit. 5. You are now ready to install the tripod accessory tray (#14). The tripod tray bracket fits into slots in the bottom of the tray (use the holes on the ends of the brackets). Use the bolts and wing nuts to attach each bracket to the tray. 6. Tighten all bolts and wing nuts to ensure proper stability. B. Before proceeding further, locate knobs #19 and #22 and tighten them finger tight after orienting the mount as illustrated in Figure 1 — for equatorial mounts only. 1. Locate the declination cable holder (where #7 fits on). Locate the declination cable (the shorter of the two cables) and attach the cable (#7) to the cable holder by tightening the thumb screw on the cable end. The thumb screw should be tightened down hard on the flat surface of the cable holder after backing off the cable about 1/4" from being fully engaged. This method helps ensure there is no slippage when using the cable. 2. You may reverse the position orientation of the Declination cable to suit your preference...
Ce manuel est également adapté pour les modèles :Instruments d'optique - 31030 (864.81 kb)
Instruments d'optique - 31030-WOS (864.81 kb)