Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
3.5-14. 3.5-14. 4.5-18. 3.5-14. 4.5-18. 50 40 50 40 50 40 5 2.9 3.6 2.2 3.6 2.2 97-97 4.0-4.0 97-97 4.0-4.0 97-97 4.0-4.0 97-97 4.0-4.0 97-97 4.0-4.0 97-97 4.0-4.0 25.4 1 25.4 1 25.4 1 25.4 1 25.4 1 25.4 1 60.3 2.37 50.3 1.98 60.3 2.37 50.3 1.98 60.3 2.37 50.3 1.98 44 1.73 44 1.73 44 1.73 44 1.73 44 1.73 44 1.73 1 click: 7 mm @ 100 m 1 click: 1/4 in @ 100 yd 1 click: 7 mm @ 100 m 1 click: 1/4 in @ 100 yd 1 click: 7 mm @ 100 m 1 click: 1/4 in @ 100 yd 1 click: 3.5 mm @ 100 m 1 click: 1/8 in @ 100 yd 1 click: 7 mm @ 100 m 1 click: 1/4 in @ 100 yd 1 click: 3.5 mm @ 100 m 1 click: 1/8 in @ 100 yd 70 55 55 40 55 40 91.44 100 45.72-. 50-. 45.72-. 50-. 45.72-. 50-. 45.72-. 50-. 45.72-. 50-. – – – – 3-Volts Lithium CR2032 3-Volts Lithium CR2032 – – – – 6 position (OFF to 5) for Green color and Red color 6 position (OFF to 5) for Green color and Red color 13.5-3.3 40.4-9.9 9.5-2.4 28.6-7.2 9.5-2.4 28.6-7.2 7.5-1.9 22.4-5.6 14.8-4.3 28.6-7.2 14.8-4.3 22.4-5.6 347 13.7 345 13.6 364 14.3 345 13.6 364 14.3 345 13.6 510 18.0 490 17.3 550 19.4 485 17.1 565 19.9 500 17.6 – – – – EU:EMC directive, AS/NZS EU:EMC directive, AS/NZS – – – – RoHS, WEEE RoHS, WEEE 3. Instructions (1) Replacement of the battery and adjusting the illumination CAUTION: When installing batteries, make sure the firearm is unloaded. Use safe firearm handling practices at all time. The PROSTAFF 5 Riflescope 3.5-14.50 SF IL and 4.5-18.40 SF IL are powered by one 3V lithium battery (CR2032). When your reticle grows dim or not light at all, you need to replace the batter y. How to replace battery 1 Hold the rheostat intensity dial tightly and turn the cover with battery cover opener 1 counter-clockwise (Fig. 3-1). Fig. 3-1 Fig. 3-2 2Take out the old battery and put one 3V Lithium Battery 2 into the compartment. Be sure (+) side to be up (Fig. 3-2). 3 Put the cover back and turn it clockwise with battery cover opener until the cover in firmly secured. *at maximum magnification **(at minimum magnification)-(at maximum magnification) ***MOA = Minute of Angle 10 11 En How to adjust illumination intensity En Turn the rheostat intensity dial to the desired color (red or green) and intensity (6 steps: OFF to 5) (Fig. 3-3). *The Nikon PROSTAFF 5 Riflescope comes with a 3V lithium battery (CR2032). *Replace the battery if the Nikon PROSTAFF 5 Riflescope is ever submerged in water or if water enters the battery chamber. Fig. 3-3 (2) Focusing 1 Look through the eyepiece with your eye positioned about 10 cm (4 in) away from the eyepiece to see the BDC reticle (Fig. 3-4), the Duplex reticle (Fig. 3-5), the Fine Crosshair w/Dot reticle (Fig. 3-6), or the Mildot reticle (MILstandard) (Fig. 3-7). Be sure your eye is positioned with proper alignment and with proper eye relief, otherwise the view will “black out.” 2 Point the objective end of the scope at the sky (NOT point it at the sun) or at a plain unpatterned wall. 3Turn the eyepiece adjustment counter-clockwise and then turn it clockwise until the reticle appears sharp. (3) Magnification •The PROSTAFF 5 Riflescope has variable magnification. For details, see “2. Specifications”. To change powers, rotate the power selector ring until the desired magnification appears adjacent to the power index dot. BDC reticle Duplex reticle Fig. 3-4 Fig. 3-5 Fine Crosshair with Dot reticle Mildot reticle (MIL standard) Fig. 3-6 Fig. 3-7 (4) Adjustment of the riflescope En Sighting through the riflescope, align the rifle with your aiming point on the target and shoot a trial round. If the bullet does not hit the aiming point, adjust the elevation and windage as follows: • If the bullet hits under the aiming point, turn the elevation adjustment turret (counter-clockwise) in the direction of the arrow marked “U” for up. If the bullet hits high, turn the elevation adjustment turret (clockwise) in the direction of the arrow marked “D” for down. • If the bullet hits to the right of the aiming point, turn the windage adjustment turret (clockwise) in the direction of the arrow marked “L” for left. If the bullet hits to the left of the aiming point, turn the windage adjustment turret (counter-clockwise) in the direction of the arrow marked “R” for right. • For the high profile turret, adjustment is made by turning the turret by hand. If the bullet hits under the aiming point, turn the turret in the direction of the arrow marked “U”. If the bullet hits to the left of the aiming point, turn the turret in the direction of the arrow marked “R”. • After the reticle has been adjusted to the point of impact, replace the turret cap for both the windage and elevation adjustment turrets. (5) Zero setting of adjustment turrets The elevation adjustment and windage adjustment turrets have a retracting system. After the reticle has been adjusted to the point of impact, pull out the elevation adjustment or windage adjustment turret. The turret can now be turned freely. Align the zero number to the index line to set the zero setting, and then release the tur...