Évaluations - 5, GPA: 4.2 ( )

Fabricant : Danby Taille : 258.76 kb Nom Fichier : Langue d'enseignement:

2 FACTORY Each time the unit is disconnected/re-connected and/or in the event of a power failure, DEFAULT SETTING the electronic circuitboard automatically defaults to the following factory setting: Humidity Setting: 60%program setting was different from the above (defaultFan Speed: Low setting) it will be necessary to re-program your settings.When the unit is switched “Off” manuallyNOTE: In the event of a power failure, all previous(using the on/off keypad) the unit will always defaultsettings are automatically erased/cancelled. If your to the last program setting that was used. Proper installation of the water tank is crucial in maintaining reliable dehumidifier WATER TANK operation. The water tank holds accumulated condensed water and, by means of a safety OPERATION switch, controls both the water level and operation of the dehumidification process. When the water tank is full and/or accidentally displaced inside the cabinet, the float switch actuator (insidethe tank) breaks contact with the safety switch. This condition results in the immediate shut down of the compressor and fan motor system, preventing moisture from being condensed. NOTE: Never tamper with or attempt to defeat the water level (safety) float switch system. 5 OPERATING INSTRUCTIONS (cont’d) DEFROST When the machine is operated at low temperatures (less than 18°C), the surface of the evaporator may accumulate a layer of frost which would reduce the efficiency of the machine. When this happens the machinewill go into periodic defrost mode. The machine will operate in temperatures down to 5°C. The time taken todefrost may vary. If the machine freezes up, it should be turned off at the power supply and re-started. If the room temperature remains below 5°C the machine should be switched off. DEHUMIDIFYING Dehumidifying is a means of removing moisture fromthe air. A dehumidifier will help to protect your homeand valued possessions from damage (swelling) caused by moisture in the air. Essentially a dehumidifier removes moisture from the air as the moist air passes over a dehumidifying (evaporator) coil. Moisture is condensed on the evaporator coil, drained, and collected inside an internal (removable) water tank located at the front of the unit. The exhausted air being returned into the roomenvironment is elevated several degrees, causing thesurrounding air temperature to increase (slightly). This process also contributes to lowering the relative humidity of the surrounding air. DEHUMIDIFYING MODE SELECTION: 1) To turn the unit on, press the ON / OFF button. 2) Press the humidity or buttons to select a desired RH operating value (30%-90%). FAN SPEED SELECTION: Select a fan speed onthe keypad. The speed you select is identified by the(illuminated) indicator light located directly above theselection made. NOTE: The fan runs constantly to circulate air and get a proper humidity reading; while fan only is running, no moisture will be removed from the air. Moisture is only removed when the compressor isrunning. AIR FILTER Your dehumidifier features a removable Air Filter. This filter is located at the front of the unit (behind the air intake grill) directly above the water tankcompartment. The air filter plays an important role in helping to reduce (minimize) dust/dirt particles from the surrounding environment. A blocked / clogged air filter reduces air intake, impacting negatively on operatingefficiency. To maintain maximum operating efficiency, the filter must be checked and cleaned regularly (every 2 weeks). More frequent cleaning may be requireddepending upon indoor air quality. IMPORTANT: Never operate the unit without the air filter in place. AIR FILTER CLEANING STEPS: 1) Pull the air filter out gently (Fig. 3). Fig. 3 Fig. 4 2) Clean the filter with a vacuum cleaner, or wash it with clean water and dry with a dry cloth. 3) Put the clean air filter back in place and continue to operate thedehumidifier. 6 OPERATING INSTRUCTIONS (cont’d) When using the continuous drain function, the PVC hose must be placed horizontally INSTALLING PVC below the drainage hole. Avoid uneven ground and folding the hose. DRAIN HOSE NOTE: Should you damage or misplace the pvc drain hose, a standard garden hosecan be used. CONTINUOUS DRAIN The function of continuous drain can be performed using the following steps: 1) To save having to periodically empty the water tank, this unit canbe configured for continuous drain. You can use the supplieddrain hose to connect to the continuous drain connector. 2) Unscrew and remove the drain cover at the rear of the unit (Fig. A). 3) Remove the soft rubber stopper, and place it in the water tank forsafe keeping (Fig. B). 4) Insert the drain hose through the hole of the drain cover (Fig. C). 5) Ensure the rubber seal ring is properly seated in the end of thehose as shown in Fig. C. 6) Connect the drain hose to the drain port (Fig. D). 7) Tighten the drain cover in clockwise direction onto the rear of the unit (Fig. D). 8) Place th...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :