Évaluations - , GPA: ( )

Instructions DeLonghi, Modèle DE500

Fabricant : DeLonghi
Taille : 87.96 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Note: The dehumidifier needs to be secured when installed on a table or a shelf. Do not sit or stand on the dehumidifier. 3. The tank must be properly positioned. 4. Castor wheels let you move the dehumidifier easily. 12 in.(30 cm)12 in.(30 cm) Choosing the proper location for the unit 1. Use the unit in a basement to help prevent moisture damage. 2. Use the unit in cooking, laundry, bathing, and dishwashing areas that have excessive moisture. 3. Use the unit to prevent moisture damage anywhere books or valuables are stored. 4. Place the unit where you want to have comfortable conditions. List of components For models equipped with pump system: • 16 ft. (5 m) clear hose with Quick-Connect connection • 3 ft. (1 m) clear hose For all other models: • 3 ft. (1 m) clear hose Required tools and assembly time Collection tank: No assembly or plumbing necessary. Continuous draining outlet: To use the Continuous Draining feature the following tools will be necessary: • 1.5mm (0.2 in.) drill bit (to drill open the draining outlet) • Drill tool The estimated assembly time is 1-2 minutes. Pump system and Quick-Connect 16ft. hose (only on models equipped with pump system): No tools necessary. The estimated assembly time is 1-2 minutes. ENGLISH 7 Disposing of the collected water Disposing of the collected water A) Empty the tank manually. When the tank is full, remove (fig.1) and empty it into a sink. When finished, replace it properly. NOTE: The tank must be positioned properly. If you hear the intermittent sound of the beep, it means the tank is not in the proper position. B) Continuous draining. Condensed water can be drained via a hose connected to the outlet located in the lower part of the tank proceeding in the following way: 1. remove the water tank. 2. Using a 5 mm drill bit, (0.2 inches) drill a hole in the base of the tank along the torus as shown in figure 2. 3. Connect a hose to the hose connector (fig. 3). Be sure the hose does not kink or bend. Make sure that the hose is not higher than the hose connection (see figure 4). NOTE: When you remove the rubber cap keep it in a safe place in case you want drain into the tank. C) Continuous draining using the pump (only on pump models) The exclusive heavy-duty pump system allows water removal of up to 13.12 feet (4m) in height. If you want the water to flow directly to a drain, connect the condensation discharge tube supplied to the connection pipe located on the lower part of the unit (Fig. 5). Select the dehumidifying function and press the PUMP button. Note: With the condensation discharge hose missing and the pump switched ON, the pump light will start blinking and the appliance will be in the stand-by position. To eliminate this problem insert the hose and switch the pump button ON. The condensation hose can be discharged into a drain. If you are using the heavy-duty pump function, the condensation hose can also be discharged through an open window. fig. 1 fig. 2Drill fig. 3 fig. 4 Hose Drain 1 PUSH 2 fig. 5 Selecting the operations Selecting the operations Stand-by position Once the power outlet is plugged in, the display will show on the left side the degree of humidity you want to reach (the default data is 60) and on the right side the display will show (for a minute) two dots, followed by the room humidity level. How to Select the Desired Humidity Level 1) Push the stand-by button. 2) Press the button to set the desired humidty level. (30% means a dry environment, 80% a humid environment). 3...