Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
(See Figure C.) 5. If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Figure C.) 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. Figure C SPECIFIC SAFETY RULES 1. WARNING! Do not mount the Halogen Light on or in any residential structure. Mounting in such a location creates a fire hazard that can result in property damage, severe personal injury, and/or death. 2. ALWAYS point the Light away from the wall, whether the unit is in use or not. If the light is accidentally pointed at the wall while it is on or while it is still hot when turned off, a fire may result. 3. Keep all flammable materials and wall hangings at least 10 feet from the mounting location. 4. Make sure to turn off the Halogen Light and unplug the unit from its electrical outlet when unattended. 5. Immediately upon turning on the Halogen Light, the Halogen Bulb become VERY hot. While operating the unit, do not touch the Halogen Bulb, or grid. 6. Avoid excessive UV radiation. Should your skin begin to feel hot while operating the Halogen Light, immediately remove yourself from the unit’s light rays. 7. Avoid serious eye injury. Do not look directly into the Halogen Bulb when operating this product. Always wear ANSI approved safety goggles when working with tools and equipment. 8. Do not touch the Halogen Bulb at any time. Oil from skin will drastically shorten the bulb’s life-span if not cleaned (with rubbing alcohol) before use. Handle with a soft, clean cloth instead. 9. Do not operate the Light with a missing or damaged Lens or Grid. 10. Do not operate the Halogen Light with the Grid open. 11. Turn off the Halogen Light, unplug its Power Cord from its 120 volt, grounded, electrical outlet, and allow it to completely cool down prior to performing any inspection, maintenance, or cleaning on the unit. 12. After its use, make sure to allow the Light to completely cool down before storing the unit. 13. Do not obstruct walkways or common areas with the cord. 14. The Light is weatherproof but not waterproof. Do not submerge the Light in water. SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. V ~ Volts Alternating Current A Amperes n No Load Revolutions o xxxx/min. Per Minute (RPM) WARNING! The warnings, precautions, and instructions discussed in this manual cannot cover all possible conditions and situations that may occur. The operator must understand that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking the Halogen Floor Shop Light, check to make sure parts on page 10 are included. If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353. Assembly Your Halogen Floor Shop Light will require some minor assembly. The Light requires special conditions for set up and operation. It is important that you read the entire manual to become familiar with the product BEFORE you use the Light. 1. Slide the Halogen Lamp onto the Steel Stand (4). Place the Mounting Bracket on the Light onto the Steel Stand (4) and thread in the Knob (1). 2. Loosen the Knob (1) to pivot the Light. The Light Pivots 180 degrees up and down. To pivot the Light, move it by the Handle at the top of the Steel Stand. NEVER touch the Halogen Light to move it or pivot it. Bulb Replacement 1. Make certain that the product is OFF and unplugged. With leather gloves on, squeeze and remove the Grid from the front of the Light. 2. Remove the Bolt from the top of the Light. 3. Pull out the Lens from the front of the Light. 4. Make certain that the Halogen Bulb (3) has had sufficient time to cool. Gently pull out the Halogen Bulb. 5. Making certain NOT TO TOUCH the new Halogen Bulb (3), insert it into the Light left side first. Do not touch the Halogen Bulb at any time. Oil from skin will drastically shorten the bulb’s life-span if not cleaned (with rubbing alcohol) before use. Handle with a soft, clean cloth instead. 6. Insert the Bolt (2) and replace the Grid. Operation 1. To turn on the Light, plug the Power Cord into a 120 volt, grounded, electrical outlet. WARNING! Always point the light away from the wall, whether the unit is in use or not. If the unit is accidentally pointed at the wall while turned on or still hot after turned off, a fire may result. 2. Unplug the light to turn it off. Inspection, Maintenance and Cleaning 1. Always unplug the Halogen Light from its electrical outlet and allow the unit to completely cool down before performing any i...