Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
Insert the S p o r t S p o t® spotlight 12 volt DC plug into the accessory socket of your vehicle or a portable 12 volt power source, such as a jump starter. 2 . To turn on the S p o r t S p o t® slide the spring-loaded power switch to the ON position (up). 3 . To turn off the S p o r t S p o t®, release the spring-loaded power switch. It will slide back to the OFF position (down). USING THE HANGING HOOK The Hanging Hook allows you to position the unit for convenient, hands-free operation. CAUTION: TO REDUCE THE RISK OF PRODUCT DAMAGE: • When Hanging Hook is in use, do not shake light. • When light is hung by the Hanging Hook, do not shake the light or object that it is hangingfrom. Do not hang the light from any electrical wires or anything that it is not secure. • Only use the Hanging Hook for hanging this unit. The Hanging Hook is not intended tosupport additional weight. Do not attach or hang anything additional to the light or risk ofbreakage may occur. USING THE BLUE-TINTED LENS To use the included blue-tinted lens: 1 . With the unit turned off, remove the protective bezel. 2 . Place the blue lens over the face of the unit in the bezel grooves. 3 . Operate the unit normally. Refer to the following illustration for guidance. 4 CSL100MV ManualEN 062007.qxp 9/26/08 11:22 AM Page 5 CAUTION: Do not operate the spotlight without either the original bezel or the blue lens inplace over the bulb assembly. CARE AND MAINTENANCE This unit is NOT waterproof. Never submerge this unit in water. If it gets dirty, gently cleanthe outer surfaces with a soft cloth moistened with a mild solution of water and detergent. Bulb Replacement 1 . Disconnect the S p o r t S p o t® from the power sourc e . 2 . Remove rubber bezel. 3. Loosen and remove six screws that secure spotlight housing. 4. Lift up and set aside the right side of the housing. 5. Remove wire spring and carefully pull out old bulb from the terminal. 6. Replace with a new H3 type, 12 volt, 100 watt bulb, available from an electrical supplyhouse or from Black & Decker (refer to the Service Information section). 7. Reverse the above procedure to re-assemble the spotlight. Note: When handling a new halogen bulb, do not touch the glass portion of the bulb. Natural oils from your hands can cause the bulb to fail. If necessary, clean the bulb with alcohol or a liquid window cleaner. Fuse Replacement (12 Volt DC Plug) If the inverter is overloaded, and the Power/Fault LED is not lit, the internal 8 amp fusemay be blown. 1. Unscrew the flange of the DC plug (counterc l o c k w i s e ) . 2. Remove the end contact, flange and fuse. 3. Inspect the fuse to see if it is good or blown. 4. Replace with a new 8 amp fuse, if needed. 5. Carefully reassemble the fuse, end contact and flange. Do not overtighten the flange( c l o c k w i s e ) . 5 CSL100MV ManualEN 062007.qxp 9/26/08 11:22 AM Page 6 Accessories Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1 - 8 0 0 - 5 4 4 - 6 9 8 6 . WA R N I N G : The use of any accessory not recommended for use with this tool could be h a z a r d o u s . Service Information All Black & Decker Service Centers are staffed with trained personnel to provide customerswith efficient and reliable power tool service. Whether you need technical advice, repair, orgenuine factory replacement parts, contact the Black & Decker location nearest you. To findyour loc...
Ce manuel est également adapté pour les modèles :Eclairage - 000 (569.22 kb)
Eclairage - 1 (569.22 kb)
Eclairage - SPORTSPOT CSL100MV (569.22 kb)