Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Using LivingColors for the first time, please read these instructions carefully and save them for future reference. By following our guidelines, you will enjoy the full functionality of Philips LivingColors. Important: -Carefully remove all parts from the packaging. -Check whether all parts are available. -The manufacturer advises the correct use of luminaires! Therefore always follow these instructions to ensure correct and safe installation and functioning of the luminaire and keep them for future reference. -The Luminaire is only suitable for wiring directly into the mains. -The Luminaire is only suitable for mounting on the ceiling. -If in doubt, consult a qualified electrician or contact your retail outlet. Ensure that you always install the luminaire to the relevant regulations. Certain regulations indicate that luminaires should be installed by a qualified electrician (e.g. Part P for the UK). -Always tighten the terminal screws firmly. -The luminaire is suitable for mounting on normal flammable surfaces. -Please mount the luminaire out of children's reach. -If the luminaire is mounted on a metallic surface, this surface must be bonded to the protective earth conductor or to the equipotential bonding conductor of the installation. -Ensure that you don't drill through electrical wires or any other obstruction in the wall or ceiling during installation. -If the luminaire is mounted on a ceiling-box or wall-box, the box must be covered with a lid first. (e.g. The Netherlands) -Electrical wiring must never be clamped or twisted between the luminaire and the mounting surface. -Always consider all the technical specifications of the luminaire. Verify the information on the label of the luminaire and in this manual. Mounting your LivingColors ceiling lamp 1.Always isolate the Power before commencing installation, maintenance or repair. (drawing 1) 2.Strip the wires as indicated in the diagram. (drawing 2) 3.If you have a connection box for ceiling lamps in your ceiling, connect the ceiling lamp directly by screwing its plate to the connection (drawing 3) 4.If you don’t have a connection box for ceiling lamps on your ceiling, find the place where cables come out of the ceiling. Drill two holes in the ceiling, as shown on drawing 4, put in plastic plugs first, and then screw the plate on the ceiling. 5.Connect the earthing cable (usually yellow with black stripes) to the earthing connection (identified by the icon) inside the base of the luminaire (drawing 5). 6.Observe the correct colour of the wiring during installation: blue (N) and brown (L). Connect these 2 wires accordingly from your power grid to the terminal blocks inside the base of the ceiling luminaire. (drawing 6). 7.Put the luminaire on the plate which you had screwed to the ceiling earlier; fix it on both sides by screwing in a screw (drawing 7). 8.Insert the connection plug from the tripod into the lamp – make sure you hear a click (drawing 8). 9.Position the lamp on the tripod and direct LivingColors towards the wall (drawing 9). LivingColors will show a short introduction of the colour possibilities. You can adjust the length of the luminaire by turning the ring in the middle of the stand, pulling the top part of the stand to the desired length, then turning the ring back to fix the position (drawing 10). You can also pull the luminaire to one or the other side to find the best position. Getting started: 1.Open the battery compartment of the remote control by sliding the button at the back. Insert 3 AAA batteries (+ and – as indicated) (drawing a). 2.Switch on LivingColors by briefly pressing the “I” (on) on the on/off button placed on the remote control (drawing c). 3.Create your own ambiance by: -Touching the desired colour on the colour wheel. You can move your finger over the colour wheel to refine the colour (drawing d) -Changing the colour saturation (adding more white to the current colour). Press on ( ) for a deep colour or on ( ) for a more pastel colour (drawing a). Ultimately you will reach the white colour. -Dimming. Increase ( ) or decrease ( ) the light intensity via the dimming buttons (drawing f). 4.Switch off LivingColors by pressing the “0” (off) button briefly. LivingColors will remember your last colour setting for your next usage (drawing c). Do more with LivingColors: 1.Automatic color-changing mode Sweep your finger around the color wheel (one full circle) and briefly press on “I” (“On”); LivingColors will then turn into the automatic color-changing mode: the lamp will start changing colors automatically. You can adjust the speed with which colors change. Speed can be adjusted clockwise, from fast (dark blue color on the color wheel) to slow (purple) (drawing g). You can tap anywhere on the color wheel. While in the automatic color changing mode, you can also adjust the saturation and brightness of the colors. To switch back to static color mode, sweep around the color wheel again, then press “0”. Alternatively, you can...
Ce manuel est également adapté pour les modèles :Eclairage - 6914630PH (2.99 mb)