Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
As you clean, the clean water in the bladder will empty and mix with the cleaning formula. Dirty water pulled out of your carpets will collect around the outside of the bladder so that clean and dirty water are always kept separate. This allows the user to maximize tank space, yet only carry one tank to and from the sink for emptying and filling. Easy to remove and clean nozzle Now, cleaning up your machine after the cleaning process is easier than ever! Simply remove the 2-in-1 Tank and remove the screw to pop out the nozzle for rinsing in the sink. Dirt, loose carpet fibers and remaining pet hair or fuzz get washed away in a snap. ReadyTools™ dial This provides either floor cleaning or above floor cleaning with the turn of a knob. If choosing above floor cleaning for upholstery, stairs, or for those creases close to the baseboards, turn knob to "TOOLS" and choose the attachment appropriate for the job. Attach tool to the flex hose and you are ready to go. Be sure to turn knob back to "FLOOR CLEANING" when done. FLOORTOOLSCLEANING 8 800.237.7691 ug310-5943_9200_608.indd 8 6/26/08 2:11:43 PM OperationBefore you clean 1.2. OperationBefore you clean 1.2. Plan activities to give your carpet time to dry. Move furniture to another area if cleaning an entire room (optional). 3. Vacuum area with a dry vacuum cleaner thoroughly before deep cleaning. 4. Plan your cleaning route to leave an exit path. It is best to begin cleaning in the corner farthest from your exit. 5. Pretreating (optional) Pretreating is recommended to improve cleaning effectiveness for heavily soiled carpet in high traffic areas such as entryways and hallways. A. Spray the BISSELL Tough Stain Pre-treat formula onto heavy traffic areas, soiled areas, or stains. B. Allow to penetrate for at least 3 minutes. C. Clean as normal, using the BISSELL ProHeat 2X machine on the high traffic setting, following the instructions below. Carpet cleaning 1. Fill the 2-in-1 Water Tank. Remove the tank from the base of the machine by lifting up the tank carry handle. Carry like a bucket to the sink. 1a. Unlatch the top of the tank from the bottom by lifting up on the tank latch which is located on the back of the tank. 1b. Remove the top of the tank by lifting up on the handle. Note how the lip on the top tank separates from the groove in the bottom tank. This placement is important when putting the tank back together. 1c. Fill the heavy duty bladder with clean hot tap water. *Do not boil or microwave water as it can destroy the bladder. 1d. Leaving the filled bottom of the tank on a flat surface, only maneuver the top of the tank. To attach the top part of the tank to the bottom, carefully hook the lip on the top tank into the groove on the bottom tank. 1 STARTHERE 4’ 2 3 4 8 7 6 5 9 10 11 12 EXIT 3’ ATTENTION: Some Berber carpets have a tendency to fuzz with wear. Repeated strokes in the samearea with an ordinary vacuum or deep cleaner may aggravate this condition. Please see Stain Removal instructions on page 14. Lip Groove (underside of bottom tank) 1. 1a. 1b. 1c. 1d. 800.237.7691 9 ug310-5943_9200_608.indd 9 6/26/08 2:11:45 PM Operation Carpet cleaning (Continued) 1e. Fasten tanks together by securing the latch in the back. Note: Remember to secure the tank latch in the back and test to make sure it is secure before picking up the tank. 2. Remove formula tank from back of machine. 2a. Fill the formula tank by first unscrewing the cap and insert. Always use genuine BISSELL formulas to maximize cleaning and for the safety of your machine. Fill formula up to the line and replace the cap and insert. Place formula tank into the slot in the back of the machine for a snug fit. 2b. If using the BISSELL 3X Concentrated Fiber Cleansing Formula: Add 3 capfuls of 3X 3. Concentrated Fiber Cleansing formula to the formula tank, and then fill with hot water to the line. 3. Set Custom Clean Dial. Simply choose one of the 4 settings (heavy traffic, normal clean, light clean, or water rinse) and the ProHeat 2X will adjust the right amount of cleaning solution to mix with the heated water to fit your cleaning need. 4. Set ReadyTools Dial to the floor cleaning setting. 5. Plug into a proper outlet and turn the power and heater switches to the ON ( I ) position.Allow 1 minute for the built-in heater to warm-up before cleaning. The ProHeat 2X will be fully warmed and will provide optimal performance after a minute of continuous heated cleaning. 6. Cleaning Strokes. While pressing the trigger, make one slow forward wet pass and another one back. Let the built-in heater, formula, and DirtLifter PowerBrushes do the work for you. WARNING: 1e. 2. 2a. RINSEWATEROR WATER FLOORCLEANINGPower SwitchHeater SwitchPower SwitchPower Switch 4. 5. Caution: Do not overwet. Take care not to run over loose objects or edges of area rugs. Stalling brush may result in premature belt failure. Note: Your machine is equipped with a circuit breaker that will automatically s...
Ce manuel est également adapté pour les modèles :Paquebots - 8920 (1.76 mb)