KX-TC1200ALB KX-TC1200ALW/KX-TC1200ALS KX-TC1200ALF/KX-TC1200NZB KX-TC1200NZW/KX-TC1200NZF Operating Instructions Charge the battery for about 15 hours before initial use. 1 Getting Started 2 Making/Answering Calls 3 Speed Dialler 4 One-Touch Dialler 5 Special Features 6 Things You Should Know Contents by Section KX-TC1200ALB PLEASE READ BEFORE USE AND SAVE. Cordless Phone Model No. KX-TC1200ALB KX-TC1200ALW/KX-TC1200ALS KX-TC1200ALF/KX-TC1200NZB KX-TC1200NZW/KX-TC1200NZF Operating Instructions

Date of purchase (found on the bottom of the unit) Name and address of dealer Attach or keep original receipt to assist with any repair under warranty. Kyushu Matsushita Electric Co., Ltd. 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan PQQX13174ZA-BM F0801-1091 D 1-C Settings 1-A Accessories 1-B Location of Controls · AC Adaptor Handset Base unit .......................one · Telephone Line Cord ..........................one IN USE/CHARGE HANDEST LOCATOR Handset Hook (6-D) Charge Co

Otherwise, the unit may not dial correctly. To redial the last number dialled Press (TALK) (REDIAL). To select the handset receiver volume Press (LOUD) while talking. .Each time you press the button, the volume level will change from LOW (preset) to HIGH. If noise interferes with the conversation Press (CH) to select a clearer channel or move closer to the base unit. Backlit handset keypad The handset dialling buttons will light when you press a button or lift the handset off the base unit, or w

The TALK indicator light must be off before programming. TALK Indicator (PAUSE) (DIRECT) (PROGRAM) 2 Enter a phone number up to 16 digits. 3 Press (DIRECT). .A beep sounds. .If a pause is required for dialling, press (PAUSE)where needed. Pressing (PAUSE)counts as one digit (5-C). Speed Dialler Section 3/4 3-B Dialling a Stored Number (TALK)and Indicator (AUTO) Memory Station Numbers 1 1 Press (TALK). .The TALK indicator lights. 2 2 Press (AUTO). 3 3 Press the memory station number ((0)to (9)). .

.If you are connected via a PBX, a longer or shorter recall time may be necessary to use PBX functions (transferring a call etc.). Consult your PBX supplier for the correct setting. .When you receive a second call during a conversation, you will hear a signal tone following the call waiting tone and the conversation will be interrupted for approximately a second. The tones are generated from the telephone company. This is not fault of the product as these events are normal. For Call Waiting Serv

Extend fully. or another cordless phone. This unit can be mounted on a wall. To Power Outlet Screws and Socket OR 8.3 cm For Australia To Telephone Plug For New Zealand To Single-Line Telephone Jack Wall Template 8.3 cm 2 2 Replace the battery and close the cover. .Insert the battery plug into the connector as shown in the picture. .Be sure wires are free from being pressed by the battery body or the handset cover. 3 3 Make sure to charge the new battery for about 15 hours. 1 1 Pull down the han

.Do not pause for over 60 seconds while storing. You cannot redial by pressing (REDIAL). .If the last number dialled was more than 24 digits long, the number will not be redialled. (HANDSET\LOCATOR) does not function. .The handset is too far from the base unit or is engaged in an outside call. The RECHARGE indicator flashes or the unit beeps intermittently. .Charge the battery fully (6-A). You charged the battery .Clean the charge contacts and charge fully, but the RECHARGE again (6-A). indicato