Évaluations - 2, GPA: 4.5
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
• The setting is canceled when you connect a digital optical cable to the recorder. Recording without creating a new group The recorder is factory set to automatically create a new group for each recording. To record without creating a new group, set the recorder as follows. MENU Jog dial While the recorder is stopped, enter the menu and select “REC Settings” - “Group REC” -“Off”. What is the group function? The group function allows you to place several tracks into one unit. For example, if you create a group for all your favorite tracks, then you can select that group to play those tracks. The following figure shows the difference between a disc on which groups are recorded and a disc on which no groups are recorded. Disc with groups recorded 12345 6 7 12345 123 Group 1 Group 3 Group 2 Disc Tracks that were not assigned to a group are treated as being part of “Group - -”. Disc with no groups recorded 1 2 4 5 6 7 8 12131415 3 Disc You can record a maximum of 255 groups on a disc. If you record a track without creating a group, but then later want to create a group for that track, refer to “Assigning tracks or groups as a new group (Group Set)” (page 49). To start/stop recording in sync with the sound source (Synchro-recording) When making a digital recording (e.g., from a CD), this function automatically starts and stops the recorder in synchronization with the sound source. This eliminates the need for separate operation of the recorder and the sound source. MENU Jog dial While the recorder is stopped, enter the menu and select “REC Settings” - “SYNC REC” - “On”. z When there is no sound from the player for about 3 seconds during synchro-recording, the recorder goes into the standby mode automatically. When the sound comes from the player again, the recorder resumes synchrorecording. If the recorder is kept in the standby mode for 5 minutes or longer, the recorder stops automatically. Notes • The pause function cannot be turned on or off manually during synchro-recording. • Do not switch the “SYNC REC” setting while recording. Recording may not be done properly. • Even when there is no sound on the sound source, there may be cases when recording does not pause automatically during synchrorecording due to the noise level emitted from the sound source. • If a silent portion is encountered for approximately 2 seconds during synchrorecording from a sound source other than a CD or an MD, a new track mark is automatically added at the point where the silent portion ends. Various ways of playback Viewing various information You can check the track name, disc name, etc. during playback. MENU Jog dial 1 Enter the menu and select “Display”. 2 Turn the jog dial to select the information you want, and then press the jog dial to enter the selection. Each turn selects the display as follows. “Lap Time” t “1 Remain” t “Tr 1 Remain A Track number Group number1) B Remaining time of the current track C Track name Artist name (Hi-MD)/ Group name (MD) Album name (Hi-MD)/ Disc name (MD) Tr Property A Track number Group number1) B Elapsed time C Track name Group name Codec information (Hi-MD)2)/ Track mode information (MD) and time and date of recording3) Property” 1) Appears when the Main play mode is set to “Group Play”. When you press the jog dial, the 2) If the case of an MP3 track that supports VBR selected information appears at A, (Variable Bit Rate), the bit rate that appears B and C. here may not match the one displayed by the SonicStage software. 3) Appears for tracks that have time stamp information. While the recorder is stopped Note Depending on the group settings, the operating conditions, and the disc settings, you may not be able to select certain indications or the indications may appear differently. z If you want to check the remaining time or the recording position while recording or in stop mode, see “Viewing various information” (page 31). Lap Time A Track number Group number1) B Elapsed time C Track name Artist name (Hi-MD)/ Group name (MD) Album name (Hi-MD)/ Disc name (MD) Selecting the play mode You can listen to tracks in various play modes. The play mode can consist of a combination of Main play mode, Sub play mode and Repeat play. • Main play mode: selects the playback unit, such as tracks or groups • Sub play mode: selects the type of play • Repeat play: selects Repeat play MENU Jog dial Playing tracks in Main play mode Selects the first track to be played in Main play mode. 1 While playing, enter the menu and select “Play Mode” “ MainPlayMode”. The Main play mode display appears. 2 Turn the jog dial to select the desired play mode, and then press the jog dial to enter the selection. Display Play mode Normal Play All tracks after the selected track are played. Group Play Tracks in a specified group are played. Artist Play1) Tracks by a specified artist are played. Album Play1) Tracks in a specified album are played. BookmarkPlay Bookmarked tracks are played. 1) Appears only for discs used in Hi-MD ...