Fabricant : Philips
Taille : 13.1 mb
Nom Fichier :
|
Facilité d'utilisation
3 To return to normal playback, press MODE repeatedly until repeat and shuffle disappear. Storing the last position played-RESUME You can store the last position played. When restarting, playback wil continues from where you have stopped. 1 Switch the slider to RESUME during playback to activate resume. y appears above resume. 2 Press 9 whenever you want to stop playback. 3 Press 2; to resume playback. yPlayback continues from where you have stopped. • To deactivate RESUME, switch the slider to OFF. y disappears from resume. Locking all buttons-HOLD You can lock all buttons of the set. When you press any key, no action will be executed then. • Switch the slider to HOLD to activate hold. y appears above resume and hold is displayed. All buttons are locked. When pressing any key, Hold is displayed. • To deactivate HOLD, switch the slider to OFF. y disappears from resume or hold. FEATURES / ACCESSORIES ESP and powersaving With a conventional portable disc player the music may stop while you are jogging for example. The ELECTRONIC SKIP PROTECTION protects this set against loss of sound caused by light vibrations or shocks. Continuous playback is ensured. ESP does not protect the set against damage caused by dropping ! • Press ESP repeatedly during playback to select either: y is shown and ESP is switched on. y disappears. Powersaving is switched on. Belt Clip 1 Align the belt clip as indicated in the illustration and press on the clip to insert its shaped pin into the hole in the set. 2 Turn the clip clockwise as indicated to lock the belt clip to the set. • To detach, gently lift the belt clip at the indicated end and turn it counter-clockwise. In-car connections (supplied or optionally available) Only use the AY 3545or AY 3548 car voltage converter (4.5 V DC, positive pole to the centre pin) and the AY 3501 car cassette adapter. Any other product may damage the set. 1 Put the set on a horizontal, vibration-free and stable surface. Make sure it is in a safe place, where the set is neither a danger nor an obstacle to the driver and the passengers. 2 Plug the voltage converter into the cigarette lighter socket (only for 12 V car battery, negative grounding), then connect the wired end with 4.5V DC input socket on the set. 3 If necessary, clean the cigarette lighter socket to obtain a good electrical contact. 4 Turn down the volume and connect the adapter cassette plug to LINE OUT/p on the set. 5 Carefully insert the adapter cassette into the car radio’s cassette compartment. 6 Make sure the cord does not hinder your driving. 7 Start playback on the set and adjust the sound with the car radio controls. • Always remove the voltage converter from the cigarette lighter socket when the set is not in use. Note: If your car radio has a LINE IN socket, it is better to connect the set to this jack instead of using the cassette adapter. Connect LINE OUT / p of the set with the LINE IN jack of your car radio with an appropriate cable. 3:14 1 2 4.5V DC 12V DC TROUBLESHOOTING Troubleshooting WARNING: Under no circumstances should you try to repair the set yourself as this will invalidate the warranty. If a fault occurs, first check the points listed, before taking the unit for repair. If you are unable to solve a problem by following these hints, consult your dealer or service center. Problem Solution No power, playback – Insert the batteries correctly. does not start – Replace the batteries. – Connect the mains adapter securely. Hold indication – Deactivate HOLD. and/or no reaction – Disconnect the set from the power to controls supply or take out the batteries for a few seconds. No sound or – Press 2; to resume playback. bad sound quality – Adjust the volume. – Check and clean the connections. – Keep this set away from active mobile phones or strong magnetic fields. Insert CD – Insert a disc, label upwards. or – Clean or replace the disc. No audio file – Wait until the steamed up lens has indication cleared. – Make sure you have inserted an audio disc or an MP3-CD. Problem Solution Disc error – Make sure the inserted CDR or CDRW indication is recorded correctly . Music file is not played – Make sure that the file names of the MP3 files end with .mp3 Missing directories on – Make sure the total number of MP3-CD files and albums on your MP3-CD does not exceed 400. – Only albums with MP3 files are shown. The disc skips tracks – Clean or replace the disc. – Make sure repeat, repeat album, shuffle or prog are not selected. Music skips or – Play the music file on your com popping sound when puter. If the problem persists, playing an MP3 file encode the audio track again and make a new CD-ROM. Oops indication – Switch ESP on. – Damaged disc. In-car use: – Clean the cigarette lighter jack No power, playback – Switch on the ignition of your car. does not start In-car use: – Insert the cassette adapter correctly. No sound or – Change the autoreverse direction of bad sound quality your car cassette player. – Let the set adjust to the...