Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
To install batteries into the player, 1. Press the CD LID OPEN button to open the CD lid. 2. Open the battery compartment cover located under the CD lid. 3. Insert the two 1.5VDC ‘AAA’ size (UM-4) alkaline batteries into the Battery Compartment following the polarity markings as indicated in the compartment. CAUTION: -Be sure that the batteries are installed correctly. Wrong polarity may damage the unit. -Please remove the batteries from the unit if you do not plan to use the unit for several weeks. -Batteries may leak chemicals and harm the electronic parts. -Dispose of old batteries promptly and properly. -Remove exhausted batteries from the unit. -Replace the batteries when the unit stops operating properly. -Never attempt to recharge “Non-rechargeable” batteries. 4. Close the battery door and completely slide it back to its original position. WARNING: UNPLUG THE ADAPTOR WHEN OPERATING THE PLAYER WITH BATTERIES. Using an adaptor (not included) to power the player, 1. Before connecting the adaptor to the player make sure that the AC voltage of the adaptor corresponds to your local AC outlet voltage. The polarity of the adaptor must match to the polarity markings next to the DC jack on the player. 2. Plug the 4.5VDC~500mA AC-DC adaptor into an AC outlet. 3. Insert the DC plug into the jack on the player. EARPHONES AND HI-FI CONNECTION Listening with Headphones Insert the plug of stereo headphones (included) into the Headphone Jack of the player. CAUTION: AVOID EXCESSIVE VOLUME LEVELS FOR LONG PERIODS OF TIME WHEN USING THE HEADPHONES. PROLONGED USE AT HIGH LEVELS MAY IMPAIR YOUR HEARING. Connecting the Player to Component Audio Systems Use a Stereo Y-Connector Cable (not included) and plug the 2 RCA plugs into the AUX input jacks on the back of your system. Plug the Stereo 3.5mm plug into the Headphone Jack on the player. NOTE: Always switch off the power before making any connections to another audio system. BASIC OPERATIONS 1. Slide the HOLD switch on the player to the “OFF” position. 2. Press the OPEN button on the CD Lid to open the CD compartment. 3. Insert a disc with the label side facing up. 4. Close the CD Lid. A click is heard when it locks into place. 5. Slide the LOCK switch (5) to the “ON” position to lock the CD Lid and activate the player. 6. Press the PLAY/PAUSE button once to start playing. 7. The display will show the total number of tracks and playing time. The player will then start playing the first track. 8. Press the VOLUME UP or VOLUME DOWN buttons to adjust the sound level. The volume range is 0-31. NOTE: This unit can also play 3 inch (8cm) single CDs without an adaptor. Do not use a CD single adaptor for these smaller discs. Remote Control Operations - With the player in the OFF position, 1. Plug the headphones into the Headphone Jack of the Remote Control. 2. Plug the Wire Remote Set into the Headphone Jack of the Main Unit. 3. Make sure the Remote Hold switch is OFF. 4. Rotate the VOLUME knob on the Remote to about the lowest setting. 5. Adjust the volume level for the Main Unit to its maximum setting. - While CD is playing, 1. Press the four function keys (PLAY/PAUSE, STOP, SKIP/SEARCH UP and SKIP/SEARCH DOWN buttons) to access the functions as described for the Main Unit. 2. Rotate the VOLUME knob on the Remote to adjust the sound level. You may need to adjust the volume on the Main Unit if the level is too high or low when using the Remote volume control. TIPS: It is recommended to slide the HOLD switches on the both Remote and Player to the “OFF” positions when: 1. The both units are put into your bag or carrying case when they are not in use. 2. The Main Unit is put in your bag or carrying case during operating. This is to prevent the unit from being accidentally turned on, resulting in draining the batteries. NOTE: Never disconnect the Remote from the Player while a CD is Playing. Stop the CD first and make sure the Player is OFF before connecting or disconnecting the Remote from the Player. Abnormal operation may occur if the Remote is connected to or disconnected from the Player during playback. To Enhance the Bass Sound Set the BBS switch to the ON position. NOTE: The bass boost performance will be increase or decrease depending on the Volume level. Turning Power On and Off To turn ON and OFF, press the following buttons after a disc is inserted into the player. To turn ON : Press PLAY/PAUSE button (playback starts) To turn OFF : Press STOP button once for standby mode. Press STOP button again to turn off the power. To Remove the Disc 1. Slide the LOCK switch (5) to its original position. 2. Press the CD LID OPEN button to open the CD compartment lid. 3. Hold the edge and gently press the center pivot as illustrated, then pick up the disc. CAUTION: WAIT FOR THE DISC TO STOP SPINNING BEFORE SLIDING THE OPEN SWITCH AND OPENING THE LID. Notes on CD-R/RW Discs - Because of non-standardized format definition/production of CD-R/RW, playback quality and performance is not gua...
Ce manuel est également adapté pour les modèles :Lecteurs - CD-600 (152.64 kb)