|
Facilité d'utilisation
See Lighting Instructionson page 14. 1. After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the remote selector switch to the REMOTE position. Note:The burners may light if handheld remote ON button was on when remote selector switch was last turned off. You can now turn the burners on and off with the handheld remote control unit. IMPORTANT: Do not leave the remote selector switch in the REMOTE position when the pilot is not lit. This will drain the battery. IMPORTANT: Be sure to press the ON/OFF buttons on the hand held remote control unit for up to 3 seconds to assure proper operation. GHRC Series Operation: 2a. Press the ON/OFF button to turn the burners on and off. When turning burners off, the pilot will remain lit. GHRCTA Series Operation: 2b. Press the AUTO/ON/OFF button on the hand-held remote control (see Figure 27). The lights to the left of the button will show AUTO, ON, or OFF. • In the ON mode, the burners will ignite. The heater is in manual mode when ON is lit. Flame Adjustment Knob Control Knob in On Position 104461 15 DESA INTERNATIONALVENT-FREE NATURAL GAS STOVE HEATER OPERATING HEATER Continued • In the AUTO mode, the thermostat in the hand-held remote unit controls the room temperature. To increase the room temperature, press the top arrow of the TEMP button. To lower the room temperature, press the bottom arrow of the TEMP button. At higher settings the heater will run longer. IMPORTANT:This remote control has been specially engineered to take an air temperature sample every minute in the auto mode. It will not respond immediately to the temperature setting being turned up or down. IMPORTANT: The hand-held remote control unit must be near the heater. Do not keep the hand-held remote control unit too close to the heater. The thermostat on the hand-held remote control unit will heat up too quickly and turn the heater off. 3. To turn the burner off, press the AUTO/ON/OFF button until OFF lights. The pilot will remain lit. IMPORTANT: To turn the pilot off, manually turn the control knob on the heater to the OFF position. LIGHTING INSTRUCTIONS SVYD18N and FSVYD18N Manual-Variable Control Models NOTICE: During initial operation of new heater, burning logs will give off a paper-burning smell. Open damper or window to vent smell. This will only last a few hours. 1. STOP! Read the safety information page 14, column 1. 2. Make sure equipment shutoff valve is fully open. 3. Press in and turn control knob clockwise to the OFF position. 4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information on page 14, column 1 . If you don’t smell gas, go to the next step. 5. Slightly depress and turn control knob counterclockwise to the PILOT position. Keep control knob pressed in for five (5) seconds (see Figure 28). Note: You may be running this heater for the first time after hooking up to gas supply. If so, the control knob may need to be pressed in for 30 seconds or more. This will allow air to bleed from the gas system. 6. With control knob pressed in, press and release ignitor button. This will light pilot. The pilot is attached to the burner (see Figure 18, page 11). If needed, keep pressing ignitor button until pilot lights. Note:If pilot does not light, contact a qualified service person or gas supplier for repairs. Until repairs are made, light pilot with match. To light pilot with match, see Manual Lighting Procedure, page 17. Ignitor Button Control Knob Figure 28 - Control Knob and Ignitor Button Location Ignitor Electrode Thermocouple Pilot Burner Figure 29 - Pilot 7. Keep control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release control knob. Note: If pilot goes out, repeat steps 3 through 7. • If control knob does not pop out when released, contact a qualified service person or gas supplier for repairs. 8. Slightly depress and turn control knob counterclockwise to the HIGH position. The burner should light. Set control knob to any heat level between HIGH and LO. VARIABLE CONTROL OPERATION The variable control valve can be set to any heat setting and flame height desired, by simply turning the control knob until that setting is attained. Even the lowest setting provides realistic, dancing yellow flames. Selecting higher settings produces greater heat output. This results in increased heating comfort. WARNING: Do not operate heater between PILOT and HIGH positions. CAUTION: Do not try to adjust heating levels by using the equipment shutoff valve TO TURN OFF GAS TO APPLIANCE Shutting Off Heater 1. Press in and turn control knob clockwise to the HIGH position. 2. Turn the control knob clockwise to the PILOT position. 3. Press in control knob and turn clockwise to the OFF Position. Shutting Off Burners Only (pilot stays lit) 1. Turn the control knob clockwise to the HIGH pos...
Ce manuel est également adapté pour les modèles :Plate - (F)SVYD18NR (674.98 kb)